Diagnostics & Errors 8-7
Error Description
Code
260 Print adjustment (position) must be -450 to 450 dots.
261 Margin adjustment (position) must be -99 to 99 dots.
262 Speed adjustment must be 0 (default), 25 (2.5 ips), 40 (4.0 ips), 60 (6.0 ips), 80 (8.0
ips), 100 (10.0 ips), or 120 (12.0 ips).
263 Primary monetary symbol must be 0 (None), 1 (Dollar), 2 (Pound), 3 (Yen), 4 (Deutsche
Mark), 5 (Franc), 6 (Peseta), 7 (Lira), 8 (Krona), 9 (Markka), 10 (Schilling), 11 (Rupee),
12 (Ruble), 13 (Won), 14 (Baht), 15 (Yuan), or 16 (Euro).
264 Secondary symbol selection must be 0 (none) or 1 (print secondary sign).
265 Monetary decimal places must be 0 to 3.
266 Character string length in the control characters packet must be 5 (MPCL control
characters) or 7 (ENQ/IMD command character).
267 Baud rate selection must be 0 (1200), 1 (2400), 2 (4800), 3 (9600), 4 (19200), 5 (38400),
6 (57600), or 7 (115200). Resend the communication settings packet.
268 Word length selection must be 0 (7 bits), or 1 (8 bits). Resend the communication
settings packet.
269 Stop bits selection must be 0 (1 bit), or 1 (2 bits). Resend the communication settings
packet.
270 Parity selection must be 0 (none), 1 (odd), or 2 (even). Resend the communication
settings packet.
271 Flow control selection must be 0 (none), 1 (DTR), 2 (CTS/RTS), or 3 (XON/XOFF).
Resend the communication settings packet.
272 Symbol set (code page) in the System Setup packet must be 0 (Internal), 1 (ANSI), 2
(DOS 437), 3 (DOS 850), 4 (1250- Latin 2), 5 (1251- Cyrillic), 6 (1252- Latin 1), 7 (1253-
Greek), 8 (1254- Turkish), 9 (1255- Hebrew), 10 (1256- Arabic), 11 (1257- Baltic), 12
(1258- Vietnamese), 13 (852- Latin 2), 14 (855- Russian), 15 (857- IBM Turkish), 16
(860- DOS Portuguese), 17 (Wingdings), 18 (Macintosh), 19 (Unicode), 20 (BIG5), 21
(GB), 22 (SJIS to SJIS), 23 (GB to GB), 24 (BIG5 to BIG5), 25 (KSC to KSC) or 26
(UTF-8).
273 Cut adjustment must be -300 to 300 dots.
282 RS232 Trailer string is too long. Use a maximum of 3 characters.
283 ENQ Trailer string is too long. Use a maximum of 3 characters.
284 The buffer type must be D (Downloadable Fonts), F (Format), or I (Image).
285 The storage device type in the memory configuration packet must be F (flash) or R
(volatile RAM).
286 The buffer size is invalid.
287 The printhead width must be 0.
288 The battery voltage must be 0 (15-volt battery) or 1 (12-volt battery).
289 The printer address specified in the communications settings packet must use exactly six
characters.
290 Action must be 0 (disable), 1 (enable), or 2 (extended) for the backfeed control packet or
the printer is active.
291 Dispense position must be 50 to 200 dots or the printer is active.
292 Backfeed distance must be 10 to 200 dots or the printer is active. The backfeed distance
can not be greater than the dispense position.
To Next Page
Loading...
