Binder KT 53 - Certificates; EC Declaration of Conformity

139 pages

Save Page as PDF

To Next Page

To Previous Page

KT (E6.1) 07/2015 Page 129/138

24. Certificates

24.1 EC Declaration of Conformity

Main Page

Table of Contents2
Safety6
Legal Considerations6
Structure of the Safety Instructions6
Signal Word Panel6
Safety Alert Symbol7
Pictograms7
Word Message Panel Structure8
Localization / Position of Safety Labels on the Unit8
Type Plate9
General Safety Instructions on Installing and Operating the Cooling Incubator10
Intended Use12
Operating Instructions12
Measures to Prevent Accidents13
Unit Description14
Unit Overview15
Instrument Panel15
Unit Rear16
Completeness of Delivery, Transportation, Storage, and Location of Installation17
Unpacking, and Checking Equipment and Completeness of Delivery17
Guidelines for Safe Lifting and Transportation17
Storage18
Location of Installation and Ambient Conditions18
Installation of the Equipment20
Spacer for Wall Distance20
Electrical Connection21
Start up22
Behavior When Opening the Door22
Functional Overview of the T4.12 Chamber Controller22
Menu Structure23
General Menu23
Quick Menu25
User" Menu25
Operating Modes26
Activating the "Control Off" Mode or Change to "Fixed Value" Operating Mode26
Performance During and after Power Failure28
Information29
Configuration of Optional Equipment30
Setting the Optional Door Heating30
Turning on / off the Optional Interior Socket31
Switching on or off the Optional Zero-Voltage Relay Control Outputs32
Functional Test of the Optional Alarm Output32
Switching on or off the Optional Object Temperature Display33
Set-Point Entry in "Fixed Value" Operating Mode34
Setting Ranges34
Entering the Set-Points Via "Quick Menu34
Entering the Set-Points Via General Menu36
Time Programs38
Starting and Running an Existing Time Program40
Cancelling a Running Time Program43
Creating a New Time Program44
Section Handling46
Temperature Setpoint47
Section Duration47
Repeating One or Several Sections Within a Time Program48
Tolerance Range49
Set-Point Ramp and Set-Point Step Modes51
Switching on or off the Optional Zero-Voltage Relay Outputs53
Calling up the Next Parameter54
Saving the Time Program and Leaving the Program Editor56
Program Interruption58
Deleting a Time Program59
Week Programs60
Starting and Running an Existing Week Program61
Cancelling a Running Week Program64
Creating a New Week Program65
Section Handling67
Temperature Setpoint68
Day of the Week68
Time of the Day69
Activity of the Shift-Point70
Switching on or off the Optional Zero-Voltage Relay Outputs70
Calling up the Next Parameter71
Saving the Week Program and Leaving the Program Editor73
Deleting a Week Program74
Key Lock75
Directly Activating the Key Lock Function76
Automatic Key Lock76
Changing the Password for Unlocking the Key Lock78
General Controller Settings79
Setup Wizard80
Date and Time Settings80
Selecting the Menu Language of the T4.12 Controller82
Setting Display Brightness82
Changing the Temperature Unit83
Defining the Data Recording Rate83
Factory Reset84
Network Configuration84
Display of the Entire Network Configuration88
RS 422 Address (with Optional RS 422 Interface)89
Display and Entry of the Chamber Configuration - for Service Purpose89
Data Transfer Via Usb Interface90
Exporting Data to USB Drive90
Importing Data from USB Drive91
Notifications and Alarms92
Notifications Overview92
Alarms Overview92
Alarm Status93
Confirming a "Set" Alarm94
Alarm Configuration and Overview95
List of Active Alarms95
History - List of All Alarms96
Activating, Deactivating, and Testing the Alarm Buzzer97
Activating / Deactivating All Alarm Functions97
Event List98
Graphical Display of the Measured Values99
Setting the Sampling Rate99
Defining the Display Range100
Selecting the Parameters101
Temperature Safety Devices102
Overtemperature Protective Device (Class 1)102
Overtemperature Safety Controller (Temperature Safety Device Class 3.1)102
Safety Controller Modes102
Setting the Safety Controller103
Over- and Undertemperature Safety Controller (Temperature Safety Device Class 3.3) (Option)106
Safety Controller Modes106
Setting the Safety Controller107
Notes on Refrigerating Operation110
Options110
Communication Software APT-COM™ 3 Datacontrolsystem (Option)110
RS 422 Interface (Option)110
Data Logger Kit (Option)111
Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)111
Zero-Voltage Relay Alarm Output (Option)112
Analog Output for Temperature (Option)113
Zero-Voltage Relay Control Outputs (Option)113
Water Protected Internal Socket (Option)114
Maintenance, Cleaning, and Service115
Maintenance Intervals, Service115
Cleaning and Decontamination116
Cleaning116
Decontamination117
Sending the Unit Back to BINDER Gmbh118
Disposal119
Disposal of the Transport Packing119
Decommissioning119
Disposal of the Unit in the Federal Republic of Germany119
Disposal of the Unit in the Member States of the EC Except for the Federal Republic of Germany120
Disposal of the Unit in Non-Member States of the EC121
Troubleshooting122
Technical Description124
Factory Calibration and Adjustment124
Over Current Protection124
Definition of Usable Volume124
KT (E6.1) Technical Data125
Equipment and Options126
Spare Parts and Accessories127
Dimensions KT 170128
Certificates129
EC Declaration of Conformity129
Product Registration132
Contamination Clearance Certificate133
For Units Located Outside North America and Central America133
For Units in North America and Central America136

Binder KT 53 - Certificates; EC Declaration of Conformity

Table of Contents

Related product manuals