What to do if my Bluetti Audio & Video Accessories display 'PV1 ISO Failure'?
If your Bluetti Audio & Video Accessories display 'PV1 ISO Failure', check the insulation resistor between the solar array and grounding for a short circuit.
What to do if my Bluetti Audio & Video Accessories display 'Phase Sequence Error'?
If your Bluetti Audio & Video Accessories display 'Phase Sequence Error', check if the grid connection meets installation requirements.
What to do if my Bluetti Audio & Video Accessories display 'GFCI Failure'?
If your Bluetti Audio & Video Accessories display 'GFCI Failure', check if the AC output PE wire is grounded.
What to do if Bluetti EP600 Storage shows PV1 Overcurrent?
To address the 'PV1 Overcurrent' error on your Bluetti storage, turn off the inverter, wait for 30 minutes, and then restart it. If the problem remains, please contact the BLUETTI support team.
What to do if Bluetti Storage shows BMS Communication Interrupted?
To address the 'BMS Communication Interrupted' error on your Bluetti storage, turn off the inverter, wait for 30 minutes, and then restart it. If the problem remains, please contact the BLUETTI support team.
What causes PV1 Voltage Low on Bluetti EP600?
Check the PV setup. Solar panels may get a low voltage without proper working conditions.
What to do if Bluetti EP600 reports a GFCI Hardware Circuit Failure?
Turn off the inverter and wait 30 minutes to restart it. If the symptom persists, please contact the BLUETTI support team.
What to do if my Bluetti Portable Generator displays Balanced Circuit Input Overcurrent?
If your Bluetti Portable Generator displays a Balanced Circuit Input Overcurrent error, turn off the inverter and wait 30 minutes before restarting it. If the problem continues, contact the BLUETTI support team.
What to do if my Bluetti Portable Generator displays USB Upgrade Failure?
If your Bluetti Portable Generator displays a USB Upgrade Failure, turn the inverter on again. If the symptom persists, please contact the BLUETTI support team.
What to do if my Bluetti Portable Generator displays BMS Charge Protection?
If your Bluetti Portable Generator displays a BMS Charge Protection error, check the details on the BLUETTI app.
Essential safety rules for operating and handling the EP600 Energy Storage System.
Precautions for safe installation and electrical connections to prevent hazards.
Key functions, applications, and characteristics of the EP600 inverter.
Environment, carrier, and angle requirements for system installation.
Step-by-step instructions for installing the EP600 system.
Step-by-step guide for safely powering on the EP600 system.
Step-by-step guide for safely powering off the EP600 system.
Common error codes, their descriptions, and solutions for system issues.
Detailed technical specifications for the EP600 inverter and B500 battery pack.
General| Shape | Rectangle |
|---|---|
| Certification | UL9540A, UL1973, UKCA, RCM, PSE, ICES, FCC, CE, CB |
| Built-in display | - |
| Suitable for outdoor use | Yes |
| Power protection features | Overheating, Reverse polarity, Under voltage |
| International Protection (IP) code | IP65 |
| Waveform | Pure sine |
| Input voltage | 150 - 500 V |
| Output voltage | 230/400 V |
| Charging source | AC, Solar |
| Battery capacity | - mAh |
| Battery technology | Lithium Iron Phosphate (LiFePO4) |
| Total output power | 6000 W |
| Output current (max) | 8.7 A |
| Operating temperature (T-T) | -20 - 50 °C |
| Operating relative humidity (H-H) | 5 - 95 % |
Weight and Dimensions| Depth | 325 mm |
|---|---|
| Width | 636 mm |
| Height | 370 mm |
| Weight | 40000 g |
To Next Page
