EasyManuals Logo

Bosch DIVAR 3000 User Manual

Bosch DIVAR 3000
94 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #26 background imageLoading...
Page #26 background image
Hardware setup
This chapter contains detailed information about the hardware installation and connection of
external equipment to the unit. The connector types and their pin signals are described. Most
of the connectors are located at the rear panel of the unit. For convenience, one USB port is
located on the front of the unit to connect a mouse or memory device.
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Keyboard connection (only DIVAR 5000 models)
Use the keyboard connection on the back of the unit to connect a Bosch Intuikey keyboard
using one of the following methods:
use the supplied RJ11 adaptor – see Connect using RJ11 adapter
strip the keyboard cable (or equivalent cable) to connect leads directly – see Connect
wires directly
For short distances (up to 30 m), standard 6-core telecom flat cable can be used to supply
signal connections for the keyboard (LTC 8558/00). Always use the Keyboard Extension Kit
(LTC 8557) for distances over 30 m between the keyboard and the DVR; this kit provides
junction boxes and cables. Maximum cable length: 30 m (using standard 6-core telecom flat
cable), or 1.5 km (using Belden 8760 or equivalent).
The appropriate power supply (11 - 12.6 VDC, maximum 400 mA) to externally power the
keyboard must be purchased separately.
Connect using RJ11 adapter
Connect the adapter as follows:
red cable to the (-) of the keyboard control connector
green cable connects to the (+) of the keyboard control connector
white cable to ground
blue cable to +12V
7
7.1
7.1.1
26 en | Hardware setup
DIVAR 2000 / DIVAR 3000 / DIVAR
5000
2016.09 | v1.0 | AM18-Q0717 Operation Manual Bosch Security Systems

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bosch DIVAR 3000 and is the answer not in the manual?

Bosch DIVAR 3000 Specifications

General IconGeneral
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)20 W
Storage temperature (T-T)0 - 93 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)-40 - 70 %
Sustainability certificatesRoHS
CertificationEMC, LVD, UL, cUL, CAN/CSA, BIS, RCM, ACMA EMC, CE, FCC
On/off switchYes
Product colorBlack, Silver
Rack capacity-
Bit rate24000 Kbit/s
Display modesLive view
Playback modesFast play, Forward, Frame by Frame, Reverse, Slow play
Input bandwidth320 Mbit/s
Number of users128 user(s)
Recording modesManual, Schedule, Stop
Output bandwidth256 Mbit/s
Maximum resolution3840 x 2160 pixels
Alarm input channels16
Video input channels16 channels
Alarm output channels3
Supported resolutions3840×2160, 1920×1080, 1280×1024, 1280×720, 1024×768, 970x576, 704x576, 352x576, 352x288, 176x144, 960x480, 704x480, 352x480, 352x240, 176x120
Video recording modes720p, 1080p
Video formats supportedH.264, H.265, M-JPEG
RS-232 ports1
Audio RCA inputs4
Networking standardsIEEE 802.3
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN (RJ-45) ports2
Supported network protocolsHTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS/DDNS, IP Filter, PPPoE, FTP
Copper ethernet cabling technology10BASE-T, 100BASE-T, 1000BASE-T
Wi-FiNo
HDD capacity- GB
HDD interfaceSerial ATA
Maximum storage capacity6 TB
Mobile operating systems supportedAndroid, iOS
Weight and Dimensions IconWeight and Dimensions
Depth323 mm
Width375 mm
Height53 mm
Weight4130 g

Related product manuals