EasyManuals Logo

Bruker BPHG 90 User Manual

Bruker BPHG 90
78 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #36 background imageLoading...
Page #36 background image
Installation
36 Z33081_00_001
6.1.1 LocationoftheBPHG90
TheBPHG90mustbeinstalledindoorsandinalocationwherethereisnodangerthatit
canbeexposedtowaterorrain.Itcanbeinstalledclosetoawallorpossiblybelowadesk
(a20cmclearancemustbeobservedtotherearandabove,forthepropercoolingofthe
generator).ThepowerandEthernetconnectionsandthesupplyofH
2
gasaremadeonthe
rearoftheinstrument,whereasthepH
2
outletislocatedonthefront.
If the gas supply line is attached to the wall, the rear side of the generator must be
accessible to permit the easy attachment of the gas capillary tube supply line with a flat
wrench.
Thefrontpanelmustbeeasilyaccessibleandvisiblefortheoperationofthegenerator.
Thegeneratormustbeinstalledonaflatsurface.Onceinstalledthefrontwheelsmustbe
blocked and the instrument must not be moved afterwards without disconnecting and
reconnectingthegassupplyline.
6.1.2 HydrogenGasSupply
ThemostcriticalprovisionfortheBPHG90isthesupplyofpurehydrogenandpriortothe
installationoftheinstrument;provisionsforthesafedeliveryofhydrogengashavetobe
made.
Differentsourcesofhydrogengascanbeusedtosupplythegenerator:
1. An independent electrolytic hydrogen gas generator producing very pure hydrogen,
99.999%atsufficientpressure(P>6bar)andflow(≥0.4NL/min).
2. A pressurised cylinder (200 bar) located in a remote room or outside the building. The
cylinderwitharegulatorsuppliesametaldistributionlinemadeofstainlesssteelorcopper
tubing. The room where the BPHG 90 is installed is equipped with an H
2
gas outlet, a
manual stop valve, a pressure regulator, a pressure gauge, a purge valve, and a flow
limiter.Theoptionalhydrogensupplypanelcontainsallnecessaryprovisions(seesection
The Optional Hydrogen Gas Supply Panel [}29])
3. A pressurised cylinder (200 bar max.) with a suitable pressure regulator. The cylinder
mustbehandledandsecuredaccordingtheprevalentsafetyregulationsandconnectedto
theBPHG90inthesamewayasaremotecylinder(seepoint2above).
Theconnection betweenthe hydrogen supply and the BPHG 90is madeby meansof a
flexiblestainlesssteeltube(suppliedwithinstrument).
TheBPHGhydrogeninletpressuremustbebetween6and10bar.
6.2 InstallationProcedure
TheBPHG90willnormally be installedandtestedby a trainedBrukerserviceengineer.
Whenevertheinstrumentneedstobemovedtoanotherlocation,careshouldbetakento
followthecorrectinstallationprocedure.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bruker BPHG 90 and is the answer not in the manual?

Bruker BPHG 90 Specifications

General IconGeneral
CategoryLaboratory Equipment
TypeHigh Pressure Homogenizer
Magnetic Field StrengthNot Applicable
Proton FrequencyNot Applicable
Flow RateData unavailable
Temperature RangeData unavailable

Related product manuals