Cisco CRS User Manual

Task: netflow : READ WRITE EXECUTE DEBUG
Task: network : READ WRITE EXECUTE DEBUG
Task: ospf : READ WRITE EXECUTE DEBUG
Task: ouni : READ WRITE EXECUTE DEBUG
Task: pkg-mgmt : READ WRITE EXECUTE DEBUG
Task: pos-dpt : READ WRITE EXECUTE DEBUG
Task: ppp : READ WRITE EXECUTE DEBUG
Task: qos : READ WRITE EXECUTE DEBUG
Task: rib : READ WRITE EXECUTE DEBUG
Task: rip : READ WRITE EXECUTE DEBUG
Task: root-lr : READ WRITE EXECUTE DEBUG (reserved)
Task: root-system : READ WRITE EXECUTE DEBUG (reserved)
Task: route-map : READ WRITE EXECUTE DEBUG
Task: route-policy : READ WRITE EXECUTE DEBUG
Task: sbc : READ WRITE EXECUTE DEBUG
Task: snmp : READ WRITE EXECUTE DEBUG
Task: sonet-sdh : READ WRITE EXECUTE DEBUG
Task: static : READ WRITE EXECUTE DEBUG
Task: sysmgr : READ WRITE EXECUTE DEBUG
Task: system : READ WRITE EXECUTE DEBUG
Task: transport : READ WRITE EXECUTE DEBUG
Task: tty-access : READ WRITE EXECUTE DEBUG
Task: tunnel : READ WRITE EXECUTE DEBUG
Task: universal : READ WRITE EXECUTE DEBUG (reserved)
Task: vlan : READ WRITE EXECUTE DEBUG
Task: vrrp : READ WRITE EXECUTE DEBUG
The following sample output displays the tasks and indicates which tasks are reserved from the show user
command:
RP/0/RP0/CPU0:router# show user tasks
Task: aaa : READ WRITE EXECUTE DEBUG
Task: acl : READ WRITE EXECUTE DEBUG
Task: admin : READ WRITE EXECUTE DEBUG
Task: atm : READ WRITE EXECUTE DEBUG
Task: basic-services : READ WRITE EXECUTE DEBUG
Task: bcdl : READ WRITE EXECUTE DEBUG
Task: bfd : READ WRITE EXECUTE DEBUG
Task: bgp : READ WRITE EXECUTE DEBUG
Task: boot : READ WRITE EXECUTE DEBUG
Task: bundle : READ WRITE EXECUTE DEBUG
Task: cdp : READ WRITE EXECUTE DEBUG
Task: cef : READ WRITE EXECUTE DEBUG
Task: config-mgmt : READ WRITE EXECUTE DEBUG
Task: config-services : READ WRITE EXECUTE DEBUG
Task: crypto : READ WRITE EXECUTE DEBUG
Task: diag : READ WRITE EXECUTE DEBUG
Task: drivers : READ WRITE EXECUTE DEBUG
Task: eigrp : READ WRITE EXECUTE DEBUG
Task: ext-access : READ WRITE EXECUTE DEBUG
Task: fabric : READ WRITE EXECUTE DEBUG
Task: fault-mgr : READ WRITE EXECUTE DEBUG
Task: filesystem : READ WRITE EXECUTE DEBUG
Task: firewall : READ WRITE EXECUTE DEBUG
Task: fr : READ WRITE EXECUTE DEBUG
Task: hdlc : READ WRITE EXECUTE DEBUG
Task: host-services : READ WRITE EXECUTE DEBUG
Task: hsrp : READ WRITE EXECUTE DEBUG
Task: interface : READ WRITE EXECUTE DEBUG
Task: inventory : READ WRITE EXECUTE DEBUG
Task: ip-services : READ WRITE EXECUTE DEBUG
Task: ipv4 : READ WRITE EXECUTE DEBUG
Task: ipv6 : READ WRITE EXECUTE DEBUG
Task: isis : READ WRITE EXECUTE DEBUG
Task: logging : READ WRITE EXECUTE DEBUG
Task: lpts : READ WRITE EXECUTE DEBUG
Task: monitor : READ WRITE EXECUTE DEBUG
Task: mpls-ldp : READ WRITE EXECUTE DEBUG
Task: mpls-static : READ WRITE EXECUTE DEBUG
Task: mpls-te : READ WRITE EXECUTE DEBUG
Task: multicast : READ WRITE EXECUTE DEBUG
Cisco IOS XR System Security Command Reference for the Cisco CRS Router, Release 4.1
OL-24740-01 95
Authentication, Authorization, and Accounting Commands
show user

Cisco CRS Specifications

General

Operating System	Cisco IOS XR
Product Type	Core Router
Form Factor	Modular Chassis
Dimensions	Varies by chassis type
Weight	Varies by chassis type
Architecture	Distributed
Switch Fabric	Multi-stage
Interface Support	Ethernet, SONET/SDH, OTN
Interfaces/Ports	Varies by line card
Port Density	Varies by line card
Routing Protocol	BGP, IS-IS, OSPF, MPLS
Management	CLI, SNMP
Power Supply	Redundant, hot-swappable
Cooling	Redundant, Hot-swappable Fan Trays
Supported Protocols	IPv4, IPv6, MPLS
Management Interfaces	Ethernet, console
Security Features	ACLs