Cisco NCS 5000 Series User Manual

DescriptionField
Specifies whether an FPD upgrade or downgrade is
required. A downgrade is required in rare cases when
the version of the FPD image has a higher major
revision than the version of the FPD image in the
current Cisco IOS XR software package.
Upg/Dng?
show fpd package Command Output: Example
Use the show fpd package command in administration EXECsystem admin exec mode to find out which
SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image package
you need for each SPA or SIP, and what the minimum hardware requirements are for each module. If multiple
FPD images are available for your card, they are listed as Subtype fpga2, fpga3, and so on.
The following example shows sample output from the show fpd package command:
sysadmin_vm:0_RP1 # show fpd package
PROTO-CXP-2XPITA BAO-MB FPGA NO 1.00 1.00 0.0
Slice-0 GN2411 YES 3.01 3.01 2.0
Slice-1 GN2411 YES 3.01 3.01 2.0
Slice-0 GN2411 YES 2.07 2.07 0.0
Slice-1 GN2411 YES 2.07 2.07 0.0
CCC FPGA YES 1.14 1.14 0.0
CCC Power-On YES 1.30 1.30 0.0
Ethernet Switch YES 1.32 1.32 0.0
BIOS FPD YES 9.10 9.10 0.0
SB Certificates NO 1.00 1.00 0.0
--------------------------------------------------------------------------------
NC6-FANTRAY Fantray FPGA NO 2.01 2.01 0.0
--------------------------------------------------------------------------------
PWR-3KW-AC-V2 DT-PriMCU NO 6.01 6.01 1.0
DT-Sec54vMCU NO 6.01 6.01 1.0
DT-Sec5vMCU NO 6.03 6.03 1.0
EM-Sec54vMCU NO 3.08 3.08 0.21
EM-Sec5vMCU NO 3.06 3.06 0.21
--------------------------------------------------------------------------------
PWR-2KW-DC-V2 DT-PriMCU NO 6.02 6.02 0.12
DT-Sec54vMCU NO 6.02 6.02 0.12
DT-Sec5vMCU NO 6.02 6.02 0.12
EM-PriMCU NO 3.06 3.06 0.21
EM-Sec54vMCU NO 3.09 3.09 0.21
EM-Sec5vMCU NO 3.07 3.07 0.21
--------------------------------------------------------------------------------
NC6-10X100G-L-K BAO-MB FPGA NO 1.00 1.00 0.0
BAO-DB FPGA NO 1.00 1.00 0.0
S2 GN2411 YES 3.01 3.01 2.0
S3 GN2411 YES 3.01 3.01 2.0
S4 GN2411 YES 3.01 3.01 2.0
S2 GN2411 YES 2.07 2.07 0.0
S3 GN2411 YES 2.07 2.07 0.0
S4 GN2411 YES 2.07 2.07 0.0
CCC FPGA YES 1.14 1.14 0.0
CCC Power-On YES 1.30 1.30 0.0
Ethernet Switch YES 1.32 1.32 0.0
BIOS FPD YES 9.10 9.10 0.0
SB Certificates NO 1.00 1.00 0.0
--------------------------------------------------------------------------------
NC6-10X100G-M-K BAO-MB FPGA NO 1.00 1.00 0.0
BAO-DB FPGA NO 1.00 1.00 0.0
S2 GN2411 YES 3.01 3.01 2.0
S3 GN2411 YES 3.01 3.01 2.0
S4 GN2411 YES 3.01 3.01 2.0
System Management Configuration Guide for Cisco NCS 5000 Series Routers, IOS XR Release 6.2.x
114
Upgrading FPD
show fpd package Command Output: Example

Cisco NCS 5000 Series Specifications

General

Brand	Cisco
Model	NCS 5000 Series
Category	Network Router
Language	English