EasyManuals Logo

Cisco RV215W Administration Guide

Cisco RV215W
149 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #110 background imageLoading...
Page #110 background image
Configuring VPN
Configuring Advanced VPN Parameters
Cisco RV215W Wireless-N VPN Firewall Administration Guide 110
9
Redundancy Endpoint To enable the device to switch to an alternate
gateway when the primary VPN connection fails, check the Enable check
box. Enter the WAN IP address or the FQDN for the redundancy endpoint.
To automatically revert to the primary VPN when the connnection is restored,
check the Rollback enable check box.
In Local Traffic Selection and Remote Traffic Selction, enter these settings:
Local/Remote IP—Select the type of identifier that you want to provide for
the endpoint:
- Single—Limits the policy to one host. Enter the IP address of the host
that will be part of the VPN in Start IP Address field. Enter the IP address
in the Start Address field.
- Subnet—Allows an entire subnet to connect to the VPN. Enter the
network address in the Start IP Address field, and enter the Subnet
Mask in the Subnet Mask field. Enter the subnet’s network IP address in
the Start Address field. Enter the subnet mask, such as 255.255.255.0,
in the Subnet Mask field. The field automatically displays a default
subnet address based on the IP address.
IMPORTANT: Make sure that you avoid using overlapping subnets for
remote or local traffic selectors. Using these subnets would require
adding static routes on the router and the hosts to be used. For example,
a combination to avoid would be:
Local Traffic Selector: 192.168.1.0/24
Remote Traffic Selector: 192.168.0.0/16
For a Manual policy type, enter the settings in the Manual Policy Parameters
section:
SPI-Incoming, SPI-Outgoing—Enter a hexadecimal value between 3 and
8 characters; for example, 0x1234.
Encryption Algorithm—Select the algorithm used to encrypt the data:
- DES
- 3DES
- AES-128
- AES-192
- AES-256

Table of Contents

Other manuals for Cisco RV215W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco RV215W and is the answer not in the manual?

Cisco RV215W Specifications

General IconGeneral
VPN support3DES, PPTP, L2TP
Ethernet LANYes
Cabling technology10/100Base-T(X)
Networking standardsIEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.1Q
VPN tunnels quantity6
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Wi-Fi bandNo
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Top Wi-Fi standardWi-Fi 4 (802.11n)
Ethernet LAN (RJ-45) ports4
Input current1.67 A
Supported protocolsPPPoE, PPTP, L2TP, RSTP, NAT, DynDNS, PAT, DMZ
Security algorithmsWEP, WPA, WPA2, WPS
Antennas quantity2
CertificationFCC Class B, CE, IC, UL, cUL, Wi-Fi, C-Tick
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)5 - 90 %
Operating relative humidity (H-H)10 - 85 %
Product colorBlack
Weight and Dimensions IconWeight and Dimensions
Width150 mm
Height30 mm
Weight300 g

Related product manuals