Clear-Com FSII-TCVR-IP-19-US - Page 6

111 pages

To Next Page

To Previous Page

FreeSpeak II for Eclipse | User Guide

10.8 United Kingdom (UKCA Mark) 109

10.9 Taiwan Statements 110

10.10 Customs Union EAEU 110

10.11 Waste Electrical and Electronic Equipment (WEEE) 111

Page 6

Main Page

Table of Contents3
Important Safety Instructions7
Safety Symbols8
Introduction to Freespeak II9
An FS II Communication System9
Freespeak II with an FSII Transceiver (1.9 and 2.4)13
Freespeak II with an FSII IP Transceiver13
FSII 1.9 Ghz/Fsii 2.4 Ghz15
National Radio Carrier Frequencies16
Installing a System18
Installing and Removing an E-IPA-HX Card18
Adding an E-IPA-HX Card to the Software18
Adding the E-Que Card for an FS II Transceiver or Splitter to the Matrix19
Connecting to Transceivers21
Clear-Com Cable Recommendations24
Operating the Wireless Beltpack26
Overview of the Wireless Beltpack26
Beltpack User Controls30
Using the Beltpack37
Programming on the Beltpack42
Introduction to Programming on the Beltpack42
Configuring the Beltpack Volume Settings44
Configuring the Beltpack Headset45
Configuring the Beltpack Microphone46
Configuring the Beltpack Display and Leds47
Configuring the Beltpack Alarm Options48
Selecting the Beltpack Role Default Set51
Selecting the Beltpack Administration51
Setting the Listen Again Option52
Control Audio on Keys C & D (Beltpack)(Advanced Menu Option Only)53
Accessing Beltpack Information53
Setting Display Mode54
Setting System Connect54
Enabling over the Air (OTA) Registration Mode from a Beltpack54
Performing a Site Survey56
Operating the FS II IP Transceiver (IPT)57
IP Rating (Protection Marking)58
FS II IP Transceiver Connector Panel58
IP Transmitter Leds58
IP Transceiver Fans and Filters59
Reset the IPT to Default61
Transceiver Standalone Mode62
Connecting the FS Transceivers to a Matrix62
Cabling the IP Transceivers67
Configuring the E-IPA-HX Card for Freespeak II67
Adding Transceivers68
Powering the Transceiver73
Upgrading the FS II IP Transceiver Firmware74
Upgrading from the Matrix74
Upgrading by USB Connection75
Port Security Settings75
Network and Synchronization75
General Network and Switching Rules76
Beltpack Support Capacities for FS II IP Transceivers76
Coverage Areas under Various Conditions77
FS II Transceiver Setup Rules and Tips77
Spare Parts78
Operating the FS II Transceiver79
IP Rating (Protection Marking)79
FS II Transceiver Connector Panel79
Cabling the FS II Transceivers80
Beltpack Support Capacities for FS II Transceivers85
Placing the Transceivers and Splitters85
Determining Coverage Areas87
Coverage Areas under Various Conditions88
FS II Transceiver Setup Rules and Tips88
Doing a Site Survey to Determine Coverage Areas89
Registering Beltpacks94
Upgrading FS II Transceiver Firmware94
Upgrading by USB Connection94
Upgrading by Wireless Connection95
Using the Freespeak II for Eclipse Splitter (FSII-SPL)96
Configuration Using a Splitter with Cat 5/6 RJ45 Connection96
Configuration Using a Splitter with Fiber Connection97
Splitter (FSII-SPL) Rear Connectors98
Splitter (FSII-SPL) Front Panel99
Using a Transceiver with a Fiber Connection99
Splitter Software Version (FSII-SPL)101
Specifications104
Freespeak II Beltpack104
Freespeak IP Transceiver105
Freespeak II Transceiver105
Freespeak II Transceiver Splitter106
Transmission Method106
Notice about Specifications106
Regulatory Compliance107
FCC Notice107
FCC/IC/EC RF Exposure Warning107
Japan DECT for Freespeakii IP Transceiver108
Industry Canada Compliance Statement108
Korean Notice108
KCC 2.4Ghz Warning109
European Union (CE Mark)109

Clear-Com FSII-TCVR-IP-19-US - Page 6

Table of Contents

Related product manuals