DACE RT25/50 - Default Chapter; Table of Contents

2
Page
Table of Contents
1.0 Foreword —————————————————————————————–—————— 3
2.0 Abbreviaons —————————————————————————————————-- 3
3.0 Introducon & Recommendaons ——————————————————–———————- 4
4.0 Specicaons
4.1 Ulma Operator ———————————————————————–——————- 5
4.2 Tritek Controller ———————————————————————–——————- 6
5.0 Operator & Site Basics
5.1 Operator Parts Idencaon ————————————————–———————— 7
5.2 Site Layout ————————————————————————————————- 8
5.3 Gate Pull & Running Forces ————————————————————————- 8
5.4 Cable Recommendaons ——————————————————–———————-- 10
6.0 Installing the Operator
6.1 Anchoring the Foundaon Plate ———————————————–——————— 11
6.2 Removing the Lid ———————————————————————–——————— 11
6.3 Placing the Operator in Manual Override ———————————–———————- 11
6.4 Securing Operator to the Foundaon Plate ——————————–————————- 12
6.5 Mounng the Rack on the Gate ———————————————–—————— 12
6.6 Placing Oil in the Gearbox —————————————————–—————————- 14
6.7 Mounng the Marker Magnet ———————————————————————- 14
7.0 Controller Basics
7.1 Tritek Control Board Layout ————————————————————————— 15
7.2 Overview of Power Connecons & Fuses ——————————————————— 15
7.3 Overview of Low Power Inputs & Outputs ——————————————————— 16
8.0 Charging Supply Opons ——————————————————————————————— 17
9.0 Menu Navigaon Overview —————————————————————————————— 18
10.0 Commissioning the Operator for the rst me ————————————————————— 19
11.0 Wiring Diagrams
11.1 Two Sets of Safety Beams (Relay Output) ——————————————————— 20
11.2 External Radio Receiver & Loop Detector ——————————————————— 21
11.3 Closing Safety Beam (FET Output & Relay Output) ——————————————— 22
11.4 Opening Safety Beam (FET Output & Relay Output) ——————————————— 23
11.5 Connecng Common External Devices ————————————————————— 24
11.6 Connecon for Relay Module ————————————————————————— 25
11.7 Electric & Magnec Locks ——————————————————————————— 26
11.8 Connecng Various Devices to Pulse & Alarm Outputs —————————————- 27
11.9 Two Synchronised Operators connected to One Set of Safety Beams ———————- 28
12.0 Control Board Funcons
12.1 Beam Sengs ——————————————————————————————— 29
12.2 Auto Close Setup ——————————————————————————————— 30
12.3 Remote Sengs ——————————————————————————————— 30
12.4 Pedestrian Entry ——————————————————————————————— 32
12.5 Light Sengs ——————————————————————————————— 33
12.6 Security Sengs ——————————————————————————————— 33
12.7 Lock Sengs ————————————————————————————————— 34
12.8 Operang Modes ——————————————————————————————— 35
12.9 GSM Sengs ——————————————————————————————— 35
12.10 Energy Saving ——————————————————————————————— 35
12.11 USB Sengs ————————————————————————————————— 36
12.12 HID Sengs ————————————————————————————————— 37
12.13 Diagnoscs ————————————————————————————————— 37
12.14 General Sengs ——————————————————————————————— 37
12.15 Time Manager ——————————————————————————————— 37
12.16 Gate Setup ————————————————————————————————— 39
13.0 Addional Features
13.1 Holiday Lockout ———————-——————————————————————— 41
13.2 Ground Loop ———————————————————————————————— 41
14.0 Upgrading Controller Soware ——————————————————————————- 42
15.0 Service Schedule ————————————————————————————————- 42
16.0 Nocaon Messages ——————————————————————————————- 43
17.0 Warning Messages ————————————————————————————————- 44
18.0 Glossary ————————————————————————————————————- 46
19.0 Technical Specicaons ——————————————————————————————— 48
20.0 Terms & Condions ————————————————————————————————— 49
21.0 Warranty & Disclaimer ——————————————————————————————— 52