Danfoss vlt FC 102 Operating Guide

Type designation
P11K
P15K
P18K
P22K
P30K
With mains disconnect [kA
rms
]
65 kA
65 kA
65 kA
65 kA
10 kA
Without mains disconnect [kA
rms
]
100 kA
100 kA
100 kA
100 kA
100 kA
Power losses and efficiency
Estimated power loss at rated maximum load [W]
(2)
278
392
465
525
698
Efficiency
(3)
0.98
0.98
0.98
0.98
0.98
1
B3+4 and C3+4 may be converted to IP21 using a conversion kit.
2
The typical power loss is at normal load conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions).
Values are based on a typical motor efficiency. Lower efficiency motors also add to the power loss in the drive and vice versa. If the switching fre-
quency is raised from nominal, the power losses may rise significantly. LCP and typical control card power consumptions are included. Further op-
tions and customer load may add up to 30 W to the losses. (Though typically only 4 W extra for a fully-loaded control card or options for slot A or slot
B, each). Although measurements are made with state-of-the-art equipment, some measurement inaccuracy must be allowed for (±5%).
3
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency.
Table 48: Mains Supply 3x380–480 V AC and 3x220Y/380–277Y/480 V AC, Normal Overload 110% for 1 minute, P37K–P90K
Type designation
P37K
P45K
P55K
P75K
P90K
Typical shaft output [kW]
37
45
55
75
90
Typical shaft output at 460 V [hp]
50
60
75
100
125
IP20/UL Open Type
(1)
B4
C3
C3
C4
C4
IP21/UL Type 1
C1
C1
C1
C2
C2
IP55/UL Type 12
C1
C1
C1
C2
C2
IP66/UL Type 4X
C1
C1
C1
C2
C2
Output current
Continuous (3x380–439 V) [A]
73
90
106
147
177
Intermittent (3x380–439 V) [A]
80.3
99
117
162
195
Continuous (3x440–480 V) [A]
65
80
105
130
160
Intermittent (3x440–480 V) [A]
71.5
88
116
143
176
Continuous kVA (400 V AC) [kVA]
50.6
62.4
73.4
102
123
Continuous kVA (460 V AC) [kVA]
51.8
63.7
83.7
104
128
Maximum input current
Continuous (3x380–439 V) [A]
66
82
96
133
161
Intermittent (3x380–439 V) [A]
72.6
90.2
106
146
177
Continuous (3x440–480 V) [A]
59
73
95
118
145
Intermittent (3x440–480 V) [A]
64.9
80.3
105
130
160
SCCR
With mains disconnect [kA
rms
]
65 kA
65 kA
10 kA
65 kA
65 kA
Without mains disconnect [kA
rms
]
100 kA
100 kA
100 kA
100 kA
100 kA
AQ267037536117en-000101 / 130R0083 | 89Danfoss A/S © 2023.09
Specifications
VLT HVAC Drive FC 102
Operating Guide

Danfoss vlt FC 102 Specifications

General

Brand	Danfoss
Model	vlt FC 102
Category	DC Drives
Language	English