Danfoss vlt FC 102 Operating Guide

Type designation
P37K
P45K
P55K
P75K
P90K
Power losses and efficiency
Estimated power loss at rated maximum load [W]
(2)
739
843
1083
1384
1474
Efficiency
(3)
0.98
0.98
0.98
0.98
0.99
1
B3+4 and C3+4 may be converted to IP21 using a conversion kit.
2
The typical power loss is at normal load conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions).
Values are based on a typical motor efficiency. Lower efficiency motors also add to the power loss in the drive and vice versa. If the switching fre-
quency is raised from nominal, the power losses may rise significantly. LCP and typical control card power consumptions are included. Further op-
tions and customer load may add up to 30 W to the losses. (Though typically only 4 W extra for a fully-loaded control card or options for slot A or slot
B, each). Although measurements are made with state-of-the-art equipment, some measurement inaccuracy must be allowed for (±5%).
3
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency.
8.3 Electrical Data, 525–600 V
Table 49: Mains Supply 3x525–600 V AC - Normal Overload 110% for 1 Minute, P1K1–P7K5
Type designation
P1K1
P1K5
P2K2
P3K0
P3K7
P4K0
P5K5
P7K5
Typical shaft output [kW]
1.1
1.5
2.2
3.0
3.7
4.0
5.5
7.5
IP20/UL Open Type
A3
A3
A3
A3
A2
A3
A3
A3
IP21/UL Type 1
A3
A3
A3
A3
A2
A3
A3
A3
IP55/UL Type 12
A5
A5
A5
A5
A5
A5
A5
A5
IP66/UL Type 4X
A5
A5
A5
A5
A5
A5
A5
A5
Output current
Continuous (3x525–550 V) [A]
2.6
2.9
4.1
5.2
–
6.4
9.5
11.5
Intermittent (3x525–550 V) [A]
2.9
3.2
4.5
5.7
–
7.0
10.5
12.7
Continuous (3x525–600 V) [A]
2.4
2.7
3.9
4.9
–
6.1
9.0
11
Intermittent (3x525–600 V) [A]
2.6
3.0
4.3
5.4
–
6.7
9.9
12.1
Continuous kVA (525 V AC) [kVA]
2.5
2.8
3.9
5.0
–
6.1
9.0
11
Continuous kVA (575 V AC) [kVA]
2.4
2.7
3.9
4.9
–
6.1
9.0
11
Maximum input current
Continuous (3x525–600 V) [A]
2.4
2.7
4.1
5.2
–
5.8
8.6
10.4
Intermittent (3x525–600 V) [A]
2.7
3.0
4.5
5.7
–
6.4
9.5
11.5
SCCR
A2/A3 with mains disconnect [kA
rms
]
50 kA
50 kA
50 kA
50 kA
50 kA
50 kA
50 kA
50 kA
A4/A5 with mains disconnect [kA
rms
]
65 kA
65 kA
65 kA
65 kA
65 kA
65 kA
65 kA
65 kA
Without mains disconnect [kA
rms
]
100 kA
100 kA
100 kA
100 kA
100 kA
100 kA
100 kA
100 kA
AQ267037536117en-000101 / 130R008390 | Danfoss A/S © 2023.09
Specifications
VLT HVAC Drive FC 102
Operating Guide

Danfoss vlt FC 102 Specifications

General

Brand	Danfoss
Model	vlt FC 102
Category	DC Drives
Language	English