Datakom D-100 MK2 - Specific Topology Configurations

123 pages

To Next Page

To Previous Page

D-100 MK2 User Manual Firmware V-6.3

K96D01-EN - 29 -

4.3. 3 PHASE, 3 WIRE, DELTA

4.2. 3 PHASE, 4 WIRE, STAR

Main Page

Table of Contents6
Installation Instructions10
Mounting11
Dimensions11
Sealing, Gasket14
Electrical Installation15
Terminal Descriptions16
Battery Voltage Input16
Ac Voltage Inputs17
Ac Current Inputs18
Digital Inputs21
Analog Sender Inputs and Sender Ground21
Charge Input Terminal22
Digital Outputs22
Port (Plug-In Module)23
J1939-Canbus Port24
Usb Device Port24
Ethernet Port (Plug-In Module)26
Wi-Fi (Plug-In Module)27
Topologies28
Selecting the Topology28
Phase, 4 Wire, Star29
Phase, 3 Wire, Delta29
Phase, 4 Wire, Delta30
Phase, 3 Wire, Delta, 2 Ct (L1-L2)30
Phase, 3 Wire, Delta, 2 Ct (L1-L3)31
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)31
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)32
Phase, 2 Wire32
Functionalities33
Ct Location Selection33
Amf Functionality33
Ats Functionality33
Remote Start Functionality33
Engine Controller Functionality34
Connection Diagrams35
AMF FUNCTIONALITY, Cts at LOAD SIDE35
AMF FUNCTIONALITY, Cts at ALTERNATOR SIDE36
Ats Functionality37
Remote Start Functionality38
Engine Control Functionality39
Terminal Description41
Technical Specifications43
Description of Controls44
Front Panel Functionality44
Pushbutton Functions45
Display Screen Organization46
Measured Parameters47
Led Lamps48
Displaying Event Logs49
Statistical Counters51
Fuel Consumption Monitoring51
Operation of the Unit52
Quick Start Guide52
Stop Mode52
Auto Mode53
Run Mode, Manual Control54
Test Mode54
Protections and Alarms55
Disabling All Protections56
Service Request Alarm56
Non-Visual Warnings61
Programming62
Resetting to Factory Defaults62
Entering the Programming Mode63
Modifying Parameter Value64
Programming Mode Exit64
Program Parameter List65
Adjust Date and Time80
Weekly Operation Schedule80
Exerciser Schedule81
Sender Configuration82
Digital Input Configuration84
Output Configuration86
Site ID String88
Engine Serial Number88
Modem1-2/Sms1-2-3-4 Telephone Numbers88
Gsm Modem Parameters89
Wifi Parameters91
Ethernet Configuration91
Wi-Fi CONFIGURATION92
Gsm Configuration93
Crank Cutting94
Overcurrent Protection (Idmt)95
Motorized Circuit Breaker Control97
J1939 Canbus Engine Support99
Sms Commands103
Software Features104
Load Shedding / Dummy Load104
Load Add / Substract105
Five Step Load Management106
Remote Start Operation107
Disable Auto Start, Simulate Mains107
Battery Charging Operation, Delayed Simulate Mains108
Dual Genset Mutual Standby Operation109
Multiple Voltage and Frequency110
Single Phase Operation110
External Control of the Unit110
Automatic Exerciser111
Weekly Operation Scheduler111
Engine Heating Operation112
Engine Idle Speed Operati̇on112
Engine Block Heater112
Fuel Pump Control113
Gas Engine Fuel Solenoid Control113
Pre-Transfer Signal113
Charging the Engine Battery114
Externally Controlled Digital Outputs114
Combat Mode114
Resetting the Controller115
Automatic Connection Topology Determination115
Zero Power at Rest116
Modbus Communications117
Parameters Required for Rs-485 Modbus Operation118
Data Formats118
Declaration of Conformity121
Maintenance121
Disposal of the Unit121
Rohs Compliance121
Troubleshooting Guide122

Datakom D-100 MK2 - Specific Topology Configurations

Table of Contents

Related product manuals