To Next PageTo Next Page
Why does my Denon AVR-1612 perform the same operations with other devices?
If operations are mirrored across devices, disable “HDMI Control” in the menu by setting it to “OFF”. To prevent linked power-offs, also set “P.Off Control” to “OFF”.
Why can't I select Audyssey on my Denon AVR-1612?
If you're unable to select Audyssey MultEQ®, Audyssey Dynamic EQ®, and Audyssey Dynamic Volume®, switch the surround mode to something other than “DIRECT”. Also, these features are unavailable when headphones are in use.
Why can't I select Dynamic EQ® and Dynamic Volume® on my Denon AVR-1612?
If you're unable to select Dynamic EQ® and Dynamic Volume®, try running Audyssey® Auto Setup.
Why can't I select RESTORER on my Denon AVR-1612?
If you can't select RESTORER, ensure that an analog signal or PCM signal (fs=44.1/48 kHz) is being input. RESTORER cannot be used for multichannel signals like Dolby Digital or DTS surround. Also, switch the surround mode to something other than “DIRECT”.
Why can't I play my iPod on my Denon AVR-1612?
If the iPod won't play, check the iPod connections, ensure the iPod control dock's AC adapter is plugged into the power outlet, and switch the input source to “DOCK”.
Why isn't USB showing up on my Denon AVR-1612 Stereo Receiver?
If “USB” isn't displayed on the menu when a USB device is connected: * Check the connection. * Ensure the USB device conforms to mass storage class or MTP standards. * Connect the USB device directly to the USB port, bypassing any USB hubs. DENON does not guarantee all USB devices will operate or receive power.
Why are file names not displayed properly on my Denon AVR-1612 Stereo Receiver?
If file names aren't displayed correctly (showing “...”, etc.), it's because the file names contain characters that the unit can't display. These characters are replaced with a period (“.”). This is normal.
Why is DTS sound not output on my Denon AVR-1612?
If DTS sound isn't being output, set “Decode Mode” in the menu to either “Auto” or “DTS”.
Why can't I select Dolby PLg or DTS NEO:6 mode on my Denon AVR-1612 Stereo Receiver?
If you can't select Dolby PLg or DTS NEO:6 mode on your Denon Stereo Receiver: * Make sure that “Speaker Config.” – “Center” or “Surround” is set to something other than “None”. This mode is unavailable for 2.0/2.1ch speaker systems. * These modes cannot be selected when headphones are in use.
Why is there no audio output with HDMI connection on my Denon AVR-1612 Stereo Receiver?
If you're not getting any sound via HDMI, first, ensure the HDMI connectors are properly connected. Then, depending on where you want the sound, go to the menu and set “HDMI Audio Out” to either “AMP” for speaker output or “TV” to output sound from your TV.
General| Audio output channels | 5.1 channels |
|---|---|
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Power output per channel (1KHz@6 Ohm) | 120 W |
| Power output per channel (20-20KHz@8 Ohm) | 80 W |
| HDMI in | 4 |
| Composite video in | 3 |
| S-Video inputs quantity | 1 |
| Speakers connectivity type | - |
| Ethernet LAN | No |
| Radio Data System (RDS) | Yes |
| Preset stations quantity | 56 |
| Analog signal format system | NTSC, PAL |
| Display | LCD |
| HDMI version | 1.4 |
| Product color | Black |
| Audio decoders | Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-HD |
| Apple docking compatibility | iPod |
| Graphical user interface (GUI) language | English, French, German |
| AC input voltage | 220-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
| Storage temperature (T-T) | -10 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 90 % |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Depth | 382 mm |
|---|---|
| Width | 435 mm |
| Height | 162 mm |
| Weight | 9200 g |
Check leakage current or line to chassis resistance before returning the set.
Cautions for servicing, electric shock, disassembly, designated parts, and post-service checks.
Properties of electric and structural parts are critical; use designated part numbers.
Procedure for initializing the receiver when the microprocessor or Digital PWB is replaced.
Details the button combinations to access various special modes.
Adjusting the idling current for the audio section.
Troubleshooting steps for power-related issues.
Steps to check and replace blown fuses.
Troubleshooting flowchart for no picture or sound output from HDMI/DVI.
Troubleshooting flowchart for audio output issues.
Troubleshooting steps when a USB device is not recognized.
Schematic diagrams for the HDMI part.
Schematic diagrams for the digital supply part.
Schematic diagrams for the MCU part.
Schematic diagrams for the MCU level charge part.
Critical parts indicated by a symbol require specific replacement parts.
Lists ICs with their functions and pin descriptions.
Details terminal functions for the EX3AV IC.
Details pin functions for the ADV7623 IC.
