To Next PageTo Next Page
How to fix no audio output on Denon AVR-1612?
If there's no audio, go through these checks: * Verify all device connections. * Check speaker connections and configurations. * Ensure the audio device is powered on. * Adjust the master volume. * Deactivate mute mode. * Select the correct input source and mode. * Disconnect headphones, as they may disable speaker output.
How to fix no sound from surround speaker on Denon Stereo Receiver?
If there's no sound from the surround speakers, make sure they are connected to the SURROUND terminals.
How to fix no sound from subwoofer on Denon AVR-1612?
If there's no sound from the subwoofer, check these: * Ensure the subwoofer connections are correct. * Turn on the subwoofer's power. * Set “Speaker Config.” – “Subwoofer” to “Yes” in the menu. * Note that if “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, sound output may vary based on the input signal or surround mode.
How to fix no sound from surround back speaker on Denon Stereo Receiver?
If there is no sound from the surround back speaker, check the following settings: * Ensure “Pre Assign” is correctly set to output audio from the surround back speakers. * Set “Speaker Config.” – “S.Back” to something other than “None” in the menu. * Set “Surr.Parameter” – “S.Back” to something other than “OFF” in the menu. * Ensure the surround mode is not set to “STEREO” or “VIRTUAL”.
How to fix no sound from front height speaker on Denon AVR-1612?
If there's no sound from the front height speaker, check these settings: * Set “Surr.Parameter” – “PLgz Height” to “ON” in the menu. * Ensure “Pre Assign” is set correctly to output audio from the front height speakers. * Set “Speaker Config.” – “F.Height” to something other than “None”.
How to fix bad radio reception on Denon AVR-1612?
If you're experiencing poor radio reception, try these steps: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Use an FM outdoor antenna. * Keep the antenna away from other connection cables.
How to fix no audio output with HDMI connection on my Denon Stereo Receiver?
If there is no audio output with the HDMI connection on your Denon Stereo Receiver: * Check the HDMI connectors to ensure they are properly connected. * If you want audio from the speakers, go to the menu and set “HDMI Audio Out” to “AMP”. * If you want audio from your TV, set “HDMI Audio Out” to “TV”.
Why is Dolby TrueHD, DTS-HD, Dolby Digital Plus audio not output from my Denon AVR-1612?
If Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio isn't being output, ensure you are using HDMI connections.
What to do if there is no video output with HDMI connection on Denon AVR-1612?
If you're not getting video output via HDMI on your Denon Stereo Receiver: * First, check that the HDMI connectors are securely connected. * Then, make sure the input source matches the HDMI connector you're using. * Also, verify that your TV supports HDCP (copyright protection). If it doesn't, video might not display correctly.
How to troubleshoot a Denon Stereo Receiver that does not turn on?
If your Denon Stereo Receiver isn't turning on: * Ensure the power plug is fully and correctly inserted into the power outlet. * If the protection circuit is active, unplug the receiver, wait 5-10 seconds, and then plug it back in.
General| Audio output channels | 5.1 channels |
|---|---|
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Power output per channel (1KHz@6 Ohm) | 120 W |
| Power output per channel (20-20KHz@8 Ohm) | 80 W |
| HDMI in | 4 |
| Composite video in | 3 |
| S-Video inputs quantity | 1 |
| Speakers connectivity type | - |
| Ethernet LAN | No |
| Radio Data System (RDS) | Yes |
| Preset stations quantity | 56 |
| Analog signal format system | NTSC, PAL |
| Display | LCD |
| HDMI version | 1.4 |
| Product color | Black |
| Audio decoders | Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-HD |
| Apple docking compatibility | iPod |
| Graphical user interface (GUI) language | English, French, German |
| AC input voltage | 220-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
| Storage temperature (T-T) | -10 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 90 % |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Depth | 382 mm |
|---|---|
| Width | 435 mm |
| Height | 162 mm |
| Weight | 9200 g |
Check leakage current or line to chassis resistance before returning the set.
Cautions for servicing, electric shock, disassembly, designated parts, and post-service checks.
Properties of electric and structural parts are critical; use designated part numbers.
Procedure for initializing the receiver when the microprocessor or Digital PWB is replaced.
Details the button combinations to access various special modes.
Adjusting the idling current for the audio section.
Troubleshooting steps for power-related issues.
Steps to check and replace blown fuses.
Troubleshooting flowchart for no picture or sound output from HDMI/DVI.
Troubleshooting flowchart for audio output issues.
Troubleshooting steps when a USB device is not recognized.
Schematic diagrams for the HDMI part.
Schematic diagrams for the digital supply part.
Schematic diagrams for the MCU part.
Schematic diagrams for the MCU level charge part.
Critical parts indicated by a symbol require specific replacement parts.
Lists ICs with their functions and pin descriptions.
Details terminal functions for the EX3AV IC.
Details pin functions for the ADV7623 IC.
