ENGLISH
Dynamic
EO
/
Volume:
OFF
~
Operating from the main unit or main remote
control unit
Press
DYNAMIC
VOLUME.
Before running Auto Setup and after running Auto Setup, if the number
of
speakers has increased or you pressed
DYNAMIC
VOLUME,
"Run
Audyssey"
is
displayed.
In
this case, either perform Auto Setup again,
or return to the setting after running Auto Setup with "Auto Setup"
- "Parameter Check" - "Restore".
fi Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations
in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic
EO
is
integrated into Dynamic Volume
so
that
as
the playback volume
is
adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
I
Middle setting prevents loud
and
soft sounds from
being much louder and softer respectively than average
sounds.
Low
setting provides the least adjustments to the
loudest and softest of sounds.
Day
Evening
About DynamicVolume
Audyssey Dynamic
EOTM
solves the problem of deteriorating sound
quality
as
volume
is
decreased by taking into account human
perception
and
room acoustics. Dynamic
EO
selects the correct
frequency response and surround levels moment-by-moment at
any user-selected volume setting. The result
is
bass response,
tonal balance, and surround impression that remain constant
despite changes
in
volume. Dynamic
EO
combines information
from incoming source levels with actual output sound levels
in
the
room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic
EO
works
in
tandem with Audyssey MultEO to
provide well-balanced sound for every listener at any volume level.
About Dynamic
EO
Audyssey Dynamic
Volume™
solves the problem of large variations
in
volume level between television programs, commercials, and
between the soft and loud passages of movies.
Dynamic Volume looksat the preferred volume setting by the userand
then monitors
how
the volume of program material
is
being perceived
by
listeners
in
real
time to decide whether
an
adjustment
is
needed.
Whenever necessary, Dynamic Volume makes the necessary rapid
or gradual adjustments to maintain the desired playback volume
level while optimizing the dynamic range. Audyssey Dynamic
EO
is
integrated into Dynamic Volume so that
as
the playback volume
is
adjusted automatically, the perceived bass response, tonal balance,
surround impression,
and
dialog clarity remain the same whether
watching movies, flipping between television channels, or changing
from stereo to surround sound content.
II
Setting (Dynamic Volume Setting)
Can
be
set
when"
Dynamic Volume"
is
set to "ON
':
Set Dynamic Volume effect.
[Selectable items]
I
Midnight
I:
High setting affects volume the most, causing
all
sounds
to be of equal loudness.
.~[.jj:e
• "Setting"
can
only
be
set when auto setup
has
been performed.
• "Setting" cannot
be
set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
• After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
•
If"
Dynamic Volume" setting
is
"OFF':
"Red"
Dynamic
EO
:
ON
/
Volume:
OFF
[~~.!2;~o~~'!]
~~-
"Green"
Dynamic
EO
/
Volume:
ON
[~~.!2~~o~~'!]
~o-
/
I'
.~[.,j:e
• "Dynamic Volume"
can
only
be
set when auto setup
has
been
performed.
• "Dynamic Volume" cannot be set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
• After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
•
When"
MultEO"
is
set to "OFF': "Dynamic Volume"
is
automatically
set to "OFF':
• "Dynamic Volume"
and"
Night Mode" cannot be used jointly.
[Selectable items]
ON
Use Dynamic Volume.
The Dynamic Volume effect will be at the level of the "DV
Setting".
~:
Do not use Dynamic Volume.
~
Operating from the main unit or main remote
control unit
Press
DYNAMIC
VOLUME.
C
Dynamic
EO
/
Volume:
ON
Dynamic
EO:
ON
/
Volume:
OFF
~
------
Dynamic
EO
/
Volume:
OFF
......
f-------
Before running Auto Setup
and
after running Auto Setup, if the number
of speakers
has
increased or you pressed
DYNAMIC
VOLUME,
"Run
Audyssey"
is
displayed.
In
this case, either perform Auto Setup again,
or return to the setting after running Auto Setup with "Auto Setup"
- "Parameter Check" - "Restore".
fa
Dynamic
EO
Audyssey Dynamic
EO
solves the problem of deteriorating sound
quality
as
volume
is
decreased
by
taking into account human perception
and room acoustics. Audyssey Dynamic
EO
works
in
tandem with
Audyssey MultEO to provide well-balanced sound for every listener
at any volume level.
•
~[.jj:e
• "Dynamic EO"
can
only
be
set when auto setup
has
been
performed.
• "Dynamic EO" cannot
be
set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
. After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
• When
"MultEO"
is
set to "OFF': "Dynamic EO"
is
automatically set
to "OFF':
• When you set "Dynamic EO" to "ON': "Tone Control" and "Night
Mode"
are switched "OFF':
[Selectable items]
~:
Use Dynamic
EO
function.
OFF
Do
not use Dynamic
EO
function.
OOperating conditions for
each
function
• Dynamic
EO
: When
"MultEO"
is
set to
"ON"
• Dynamic Volume: When "Dynamic EO"
is
set to
"ON"
• Setting: When "Dynamic Volume"
is
set to
"ON"
II
MultEO
PI
Dynamic
EO
[II
DynamicVolume
)J
(m
Setting
For
details
on
adjusting individual parameters, see "Adjusting the parameters"
(&page
46).1
50
To Next Page
Loading...
