ENGLISH
__
L
..
___
t
'0,
, ,
, ,
~~:
&Symbols used
to
indicate buttons in this manual
Button located on both the main unit and the remote control
unit
~
BUTTON
Button only
on
the main unit
~
<BUTTON>
Button only
on
the remote control unit
~
[BUnON)
The strength
of
both the XM satellite
and
terrestrial signals
can
be
checked at menu "Input Setup" - "Antenna Aiming"
(Gr'page
431.
5
Press
TUNING
and select channel 0
(XMOOO).
The radio
ID
is
shown on the display.
Radio
ID
:':1'1000
F.:AD
I
[I
!Co
***:t:*:+:*,+:
.-
Presetting Radio Stations
(Preset Memory)
Your favorite broadcast stations
can
be preset so that you can
tune
them
in
easily. Up to 56 stations
can
be preset.
1Tune
in
the broadcast station you want to preset.
2Press
[MEMORY).
3
Press
SHIFT
to
select the block
(A
to G)
in
which the
station is to be preset.
Checking the
XM
Signal Strength and
Radio
10
• The channel switches continuously when
TUNING
is
pressed and
held.
• The artist name, track name, category and reception level
can
be
checked by pressing
<STATUS>.
• The time for which the on-screen display
are
displayed
can
be
set
at menu "Manual Setup" - "Option Setup" - "On-Screen Display"
(Gr'page
361.
1
Either turn
<SOURCE
SELECT>
or press
[SAT
TU
1/2]
to select
"XM".
3
Use
TUNING
to
select the station.
When the station
is
tuned
in,
the name of the track and artist
are displayed
2
Set
[SOURCE
CONTROL1]
to
"AUDIO" and
[SOURCE
CONTROL
2)
to "TUNER".
(Gr'page
65 "Remote Control Unit Operations")
IBasic Operation
TUNING
<][>
~
[SAT
TU1/2]
SHIFT
PRESET
6
\j
<STATUS>
<SOURCE
SELECT>
cb
[Front]
I
[Rear]
SHIFT
-+---©
TUNING~
[CHANNEL
+/-]
~
6
\j
<1
[>
--'----(@
[SOURCE
1_
~--~lr~;"
[SOURCE
CONTROL
1]
r~~
I
CONTROL
2]
~
[SAT
TU
1/2]
TUNING
----J~j
to.;
;cp:-:
, ,
.-.--',--,
'-'-1-:- 6
\j
<1
[>
[MEMORy)-r
~6f
I
1
Either turn
<SOURCE
SELECT>
or press
[SAT
TU
1/2)
to select
"XM".
2
Press
<STATUS>
until "SIGNAL" appears on the
display.
The display will switch
as
shown below, depending
on
the
reception conditions.
Display
Status
GOOD Signal strength
is
good
MARGINAL Signal strength
is
marginal
WEAK Signal strength
is
weak
NO
No signal
3
Adjust the position
of
the antenna until "SIGNAL:
GOOD" is shown on the display.
4
Press
<STATUS>
until the station you want
to
check
(example:
"XMOOl")
is displayed.
4
Press
<PRESET>
or
CHANNEL
+- to select the preset
number
(1
to 8).
5Press
[MEMORY]
again to complete the setting.
To
preset other stations, repeat steps 1 to
5.
'N.na
Preset stations are erased by overwriting them.
57
To Next Page
Loading...
