ENGLISH
[Selectable items]
.11]
5B
CH
Out (for 2-channel sources)
Determine whether to use surround
back
speakers.
ON
OFF
The
surround
back
channel signal
is
played.
The
surround
back
channel signal
is
not played
Tone
Adjust the tonal quality of the sound.
Bil
Tone
Control
Turn
tone adjustments off.
udyssey Settings
ect room equalizer for current environment.
mMultEQ
Select the type of room correction desired from the following list:
The tone cannot
be
adjusted when
in
the DIRECT mode.
1m
Bass
Adjust low frequency range
(bass).
-n·o-
When the "Dynamic EO" setting
is
"ON': setting
is
not possible.
[Selectable items]
ON
Playback without tone adjustment.
~:
Allow tone adjustment (treble, bass)
[Selectable items]
Audyssey
Optimize frequency response of
all
speakers.
Audyssey
Byp.
UR
Optimize frequency response of speakers
except front
Land
R speakers.
Audyssey
Flat
Optimize frequency response of
all
speakers
to flat response.
Manual
Apply frequency response set
with
"Manual
EO"
(02W'page
34)
OFF
I:
Turn equalizer off.
• Audyssey
---
Audyssey Byp.
L/R
~
C
OFF
Manual
---
Audyssey Flat
-----J
-6dB
-
-HidB
[Variable range]
Attenuate subwoofer level when using
EXT
IN
mode.
[Selectable items]
Set this to "ON" if the subwoofer channel level seems too high when
playing audio signal.
ON
:
The
input from the subwoofer channel
is
attenuated.
~:
The
input from the subwoofer channel IS not attenuated.
Usually use
in
this mode.
Bi1
5ubwoofer
lID
5W
ATT (5UBWOOFERATT.)
I
"Bass" and "Treble"
can
be
set when "Tone Control"
is
set to "ON':
11
Treble
Adjust high frequency range (treble).
Turn
subwoofer output
on
and
off.
[Selectable items]
~:
The
subwoofer
is
used.
OFF
.
The
subwoofer
is
not used.
II
Default
Resets the settings to the default values.
[Variable range]
-6dB
-
-HidB
~
Operating from the main unit or main remote
control unit
Press
MULTEn.
• When "Audyssey", Audyssey
Byp.
UR"
or "Audyssey Flat"
is
selected, "
~~::'.'i,'bSEY
" lights.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed
without
increasing the number of speakers measured, only
"~~::'.'i,'bSEY"
lights.
• "Audyssey", "Audyssey Byp.
UR"
and "Audyssey Flat"
can
be
selected after the auto setup procedure
has
been performed.
• After performing
"Auto
Setup", the
"MultEO"
setting automatically
becomes"
Audyssey".
• If the settings of speakers for
which"
None"
has
been determined
at "Auto Setup" are changed, "Audyssey': "Audyssey Byp
UR"
and
"Audyssey Flat" cannot
be
selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with "Auto
Setup" - "Parameter Check" - "Restore".
• MultEO and Manual
EO
set to
"Not
Used" with "Manual Setup"
- "Audio Setup" - "EO Preset" - "EO Customize"
10000page
34)
on
the menu, cannot
be
selected.
• When using headphones,
"MultEO"
is
set
to
"OFF':
49
I
For
details on adjusting individual parameters, see "Adjusting
the
parameters"
(Gf'page
46).
To Next Page
Loading...
