Devatec ELECTROVAP MC2 - Installation - Step 6: 3-Phase Wiring (ELMC 50, 60, 90); ELMC 50;60 and ELMC 90 3-Phase Wiring Diagrams

60 pages

Save Page as PDF

To Next Page

To Previous Page

34 Pictures for illustrating purposes only

ELECTROVAP MC2 STEAM BATH

Installation - Step 6

ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A SKILLED AND QUALIFIED PERSONNEL

Main Page

Table of Contents2
Safety Information3
Warnings & Safety Symbols3
Delivery and Storage3
General4
Correct Use4
Water4
Electricity4
Product Accreditation5
What Is in the Box7
Delivery Contents7
Dimensions & Weight8
Humidifier Component Parts9
ELMC 5-30 Humidifier Split View9
Installation Steps10
Step 1 - Placing and Wall Attachement10
- Installation11
- How to Install the Humidifier on Wall11
- Installation on Wall12
- Drilling Distances in MM12
- Recommendations on Water Tapping13
- Softened Water13
- Recommendations13
Step 2 - Water Connection13
- Steam Distribution Nozzle14
- Steam Nozzle Selection Table14
- Wall Installation14
- Steam Outlet15
- Steam Hose Selection15
- Radius of Bend for Steam Hose15
- Condensate Draining16
- Recommended Installation17
- Positioning17
- Attachement17
Step 5 - Temperature Sensor17
- Time Bath18
- 3 Contact Remote Control Model18
- Option - Emergency Button18
- Perfume Dispensor18
- Recommendation19
- Electrical Tables20
- MC2 Steam Bath Generator in 2 X 220V - 50/60 Hz20
- MC2 Steam Bath Generator in 2 X 230V - 50/60 Hz20
- MC2 Steam Bath Generator in 3 X 208V - 50/60 Hz21
- MC2 Steam Bath Generator in 3 X 220V - 50/60 Hz21
- MC2 Steam Bath Generator in 3 X 230V - 50/60 Hz22
- MC2 Steam Bath Generator in 3 X 380V - 50/60 Hz22
- MC2 Steam Bath Generator in 3 X 400V - 50/60 Hz23
- MC2 Steam Bath Generator in 3 X 415V - 50/60 Hz23
- MC2 Steam Bath Generator in 3 X 480V - 50/60 Hz24
- MC2 Steam Bath Generator in 3 X 575V - 50/60 Hz24
- MC2 Steam Bath Generator in 3 X 600V - 50/60 Hz25
- 2 X 220-230V26
- 3 X 380-400 V Without Neutral26
- 3 Phases + Neutral: 3 X 380-400 V26
Step 6 - Electrical Connections26
- Transfomer (Option)28
- Steam Bath Control36
- Circuit Board Ref: 500102/2836
- Setting up37
- System Management - User Information Menu38
Humidifier Status Menu40
Configuration Changing Menu41
- Cylinder Maintenance Guide44
- Estimated Cylinder Maintenance Curve44
- Length of the Genuine Stainless Steel Electrode Plates44
- Points to Check in Case of Arcing45
- Warnings45
- Routine Service45
- Maintenance - Check Points45
- Maintenance - Service & Alerts46
- 50 Hours after Switching on46
- Service Time Elapsed46
- Service Time Overdue46
- Contactor Coil Failure P147
- Contactor Blocked P247
- Inlet Water Valve P347
- Clean Cylinder + Drain Valve P848
- Water Leakage Detection P648
- See Drain Circuit P548
- No Inlet Water P448
- Torroidal Transformer Wiring Method49
- Connecting the Ti Power Cable into the Contactor49
- Electrovap MC2 from 208V to 230V49
- Electrovap MC2 from 380V to 690V49
- Replacing the Steam Cylinder50
- Cleaning the Cleanable Steam Cylinder50
- Maintenance - Valves51
- Drain Valve Maintenance51
- Inlet Valve Maintenance52
- Maintenance - Spares List53

Devatec ELECTROVAP MC2 - Installation - Step 6: 3-Phase Wiring (ELMC 50, 60, 90); ELMC 50;60 and ELMC 90 3-Phase Wiring Diagrams

Table of Contents