DURKOPP ADLER Class 271 - Part 2: Installations Instructions Class 271-274 Direct Drive

Contents Page:
Part 2: Installations Instructions Class 271-274 Direct Drive
1. Scope of Delivery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. General Notes and Transport Guards
. . . . . . . . . . . . . . . . 7
3. Assembling the Stand
3.1 Assembling the Stand Parts . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Completing the Table Top and Attaching to the Stand . . . . . . . . 9
3.2.1 Machines without Edge Trimmer . . . . . . . . . . . . . . . . . . . . 9
3.2.2 Machines with an Edge Trimmer . . . . . . . . . . . . . . . . . . . . 11
3.3 Setting the Work Height . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. Attaching the Machine Head
4.1 Inserting the Machine Head . . . . . . . . . . . . . . . . . . . . . . . 13
5. Sewing Drives
5.1 Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Employment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3 Attaching the Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4 Attaching the Controller . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.5 Attaching the Cable Duct . . . . . . . . . . . . . . . . . . . . . . . . 15
5.6 Attaching the Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6. Electrical Connection
6.1 Checking the Mains Voltage . . . . . . . . . . . . . . . . . . . . . . . 17
6.2 Potential Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.3 Attaching and Connecting the Sewing Light Transformer
(Optional Equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.1 Connection to the DA220C Controls . . . . . . . . . . . . . . . . . . 18
6.3.2 Connection to the DA40MS02 Controls . . . . . . . . . . . . . . . . . 19
6.4 Connection Sockets on the DA220C and DA40MS02 Controls . . . . 20
6.5 Connecting the DA220C Controls . . . . . . . . . . . . . . . . . . . . 20
6.6 Connecting the DA40MS02 Controls . . . . . . . . . . . . . . . . . . 20
6.7 Verifying the Direction of Rotation of the Sewing Drive . . . . . . . . 21
6.8 Verifying the Positioning . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.9 Machine-specific Parameters . . . . . . . . . . . . . . . . . . . . . . 22
6.9.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.9.2 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.10 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GB