7. Operating and Setting the Direct-current Positioning Drive
DC1500/DA220C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.1 .Operating and Indicator Elements of the DA220C Controls . . . . . 24
7.1.1 Changing Parameter Values at the Operator Level in the
DA220C controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.1.1.1 Sequentially Calling up and Changing Parameters at the
Operator Level of the DA220C controls
DA220C . . . . . . . . . . 25
7.1.1.2 Directly Calling Up and Changing Parameters at the
Operator Level in the DA220C controls . . . . . . . . . . . . . . . . 26
7.1.2 Reducing the Maximum Speed at the DA220C controls . . . . . . . 26
7.1.3 Parameter List for the Operator Level of the DA220C Controls
. . 27
7.1.4 Changing Parameter Values at the "Technician Level" and the
"Supplier Level" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.1.5 Setting the Positions at the DA220C Controls . . . . . . . . . . . . 29
7.1.6 Setting Machine-specific Parameters at the DA220C controls . . . 31
7.1.6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.1.6.2 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.1.6.3 Table of Machine-specific Parameters for the DA220C Controls . . 31
7.1.7 Master Reset at the DA220C Controls . . . . . . . . . . . . . . . . 32
7.1.8 Status and Error Messages . . . . . . . . . . . . . . . . . . . . . . 33
7.2 V810 Control Panel (Optional Equipment) . . . . . . . . . . . . . . 34
7.2.1 Operating and Indicator Elements at the V810 Control Panel . . . . 34
7.2.2 Functions of the Keys at the V 810 Control Panel . . . . . . . . . . 34
7.2.3 Meanings of the Symbols in the V810 Control Panel . . . . . . . . . 35
7.2.4 Changing Parameter Values in the Operator Level . . . . . . . . . . 36
7.2.5 Reducing the Maximum Speed . . . . . . . . . . . . . . . . . . . . 36
7.2.6 Changing the Parameter values in the " Technician Level "
and in the "Supplier Level" with the V810 Control Panel . . . . . . . 37
7.2.7 Setting the Positions with the V810 Control Panel . . . . . . . . . . 38
7.2.8 Setting Machine-specific Parameters with the V810 Control Panel . 39
7.2.9 Master Reset with the V810 Control Panel . . . . . . . . . . . . . . 39
7.2.10 Status and Error Messages in the V810 Control Panel . . . . . . . 39
7.3 V820 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.3.1 Operating and Indicator Elements in the V820 Control Panel . . . . 40
7.3.2 Functions of the Keys in the V820 Control Panel . . . . . . . . . . . 40
7.3.3 Meaning of the Symbols in the V820 Control Panel . . . . . . . . . 42
7.3.4 Changing Parameter Values in the Operator Level . . . . . . . . . . 43
7.3.5 Reducing the Maximum Speed . . . . . . . . . . . . . . . . . . . . 43
7.3.6 Quick Information and Quick Entry of Setting Values (HIT . . . . . . 43
7.3.7 Changing Parameter Values in the "Technician Level "
and the "Supplier Level" with the V820 Control Panel . . . . . . . . 44
7.3.8 Setting the Positions with the V820 control panel . . . . . . . . . . 45
7.3.9 Setting Machine-specific Parameters with the V820 Control Panel . 46
7.3.10 Master Reset with the V820 Control Panel . . . . . . . . . . . . . . 46
7.3.11 Status and Error Messages in the V820 Control Panel . . . . . . . 47
7.3.12 Seam Programming with the V820 Control Panel . . . . . . . . . . 47
To Next Page
Loading...