ELTEX MES23xx User Manual

MES53xx, MES33xx, MES23xx Ethernet Switch Series 54
no sntp authenticate
Set the default value.
sntp trusted-key key_number
key_number:
(1..4294967295);
By default,
authentication is
disabled
Require authorization of the system that is used for
synchronization via SNTP by the specified key.
- key_number - key number.
no sntp trusted-key key_number
Set the default value.
sntp broadcast client enable
{both | ipv4 | ipv6}
-/denied
Allow multicast SNTP client operation.
no sntp broadcast client enable
Set the default value.
sntp anycast client enable {both
| ipv4 | ipv6}
-/denied
Allow the operation of SNTP clients that support packet
transmission to the nearest device in a group of receivers.
no sntp anycast client enable
Set the default value.
sntp client poll timer seconds
seconds:
(60…86400)/24
Set polling time of SNMP server.
no sntp client poll timer
Set the default value.
sntp client enable
{fortygigabitethernet fo_port |
tengigabitethernet te_port |
port-channel group | oob| vlan
vlan_id}
gi_port: (1..8/0/1..48);
te_port: (1..8/0/1..24);
fo_port: (1..8/0/1..4)
group: (1..16);
vlan_id (1..4094)
/denied
Allow the operation of SNTP clients that support packet
transmission to the nearest device in a group of receivers, as
well as broadcast SNTP clients for the selected interface.
- for the detailed interface configuration, see Interface
Configuration Section.
no sntp client enable
{fortygigabitethernet fo_port |
tengigabitethernet te_port |
port-channel group | oob | vlan
vlan_id}
Set the default value.
sntp unicast client enable
-/denied
Allow unicast SNTP client operation.
no sntp unicast client enable
Set the default value.
sntp unicast client poll
-/denied
Allow sequential polling of the selected unicast SNTP servers.
no sntp unicast client poll
Set the default value.
sntp server {ipv4_address |
ipv6_address |
{ipv6_link_local_address}%{vlan
{integer} | ch {integer} | isatap
{integer} | {physical-port-name}}
| hostname} [poll] [key keyid]
hostname: (1..158)
characters
keyid: (1..4294967295)
Set the SNTP server address.
- ipv4_address - Ipv4-address of a network node;
- ipv6_address - Ipv6-address of a network node;
- ipv6z-address - Ipv6z-address of a network node for pinging.
Address format {ipv6-link-local-address}%{interface-name};
ipv6-link-local-address - local link IPv6 address;
interface-name - name of the source interface in the
following format:
vlan {integer} | ch {integer} | isatap {integer} | {physical-
port-name}
- hostname - domain name of the network node;
- poll - enable polling;
- keyid - key identifier;
no sntp server {ipv4_address |
ipv6_address |
{ipv6_link_local_address}%{vlan
{integer} | ch {integer} | isatap
{integer} | {physical-port-name}}
| hostname}
Delete the server from the NTP server list.
clock dhcp timezone
-/denied
Get the timezone and daylight saving data from the DHCP
server.
no clock dhcp timezone
Prohibit the receipt of the timezone and daylight saving data
from the DHCP server.
Interface configuration mode commands
Command line prompt in the interface configuration mode is as follows:
console(config-if)#
Table 5.26. List of system time configuration commands in the interface configuration mode
Command
Value/Default value
Action
sntp client enable
-/denied
Allow the operation of SNTP clients that support packet
transmission to the nearest device in a group of receivers, as

ELTEX MES23xx Specifications

General

Brand	ELTEX
Model	MES23xx
Category	Switch
Language	English