Endress+Hauser Proline Promass E 100 - Device Operation and Configuration

108 pages

To Next Page

To Previous Page

Operation options Proline Promass E 100 Modbus RS485

36 Endress+Hauser

8 Operation options

8.1 Overview of operating options

A0017760

1 Computer with "FieldCare" or "DeviceCare" operating tool via Commubox FXA291 and service interface

2 Control system (e.g. PLC)

Main Page

Table of Contents3
About this Document5
Document Function5
Symbols5
Safety Symbols5
Electrical Symbols5
Tool Symbols5
Symbols for Certain Types of Information6
Symbols in Graphics6
Documentation6
Standard Documentation7
Supplementary Device-Dependent Documentation7
Registered Trademarks7
Safety Instructions8
Requirements for the Personnel8
Designated Use8
Workplace Safety9
Operational Safety9
Product Safety10
Security10
Product Description11
Product Design11
Device Version with Modbus RS485 Communication Protocol11
Incoming Acceptance and Product12
Identification12
Incoming Acceptance12
Product Identification12
Transmitter Nameplate13
Sensor Nameplate13
Promass 100 Safety Barrier Nameplate15
Symbols on Measuring Device15
Storage and Transport16
Storage Conditions16
Transporting the Product16
Measuring Devices Without Lifting Lugs16
Measuring Devices with Lifting Lugs17
Transporting with a Fork Lift17
Packaging Disposal17
Installation18
Installation Conditions18
Mounting Position18
Environmental and Process Requirements20
Special Mounting Instructions21
Mounting the Measuring Device22
Required Tools22
Preparing the Measuring Device23
Mounting the Measuring Device23
Post-Installation Check23
Electrical Connection24
Electrical Safety24
Connection Conditions24
Required Tools24
Requirements for Connecting Cable24
Terminal Assignment25
Pin Assignment, Device Plug28
Shielding and Grounding29
Preparing the Measuring Device29
Connecting the Measuring Device29
Connecting the Transmitter30
Connecting the Safety Barrier Promass 10031
Ensuring Potential Equalization32
Special Connection Instructions32
Connection Examples32
Hardware Settings33
Enabling the Terminating Resistor33
Ensuring the Degree of Protection34
Post-Connection Check34
Operation Options36
Overview of Operating Options36
Structure and Function of the Operating Menu37
Structure of the Operating Menu37
Operating Philosophy38
Displaying the Measured Values Via the Local Display (Optionally Available)38
Operational Display38
User Roles and Related Access Authorization40
Access to the Operating Menu Via the Operating Tool41
Connecting the Operating Tool41
Fieldcare41
Devicecare43
System Integration44
Overview of Device Description Files44
Current Version Data for the Device44
Operating Tools44
Modbus RS485 Information44
Function Codes44
Register Information45
Response Time45
Data Types45
Byte Transmission Sequence46
Modbus Data Map47
Commissioning49
Function Check49
Establishing a Connection Via Fieldcare49
Configuring the Measuring Device49
Setting the System Units49
Selecting and Setting the Medium52
Interface53
Configuring the Low Flow Cut off55
Configuring the Partial Filled Pipe56
Advanced Settings57
Defining the Tag Name57
Calculated Values57
Carrying out a Sensor Adjustment58
Configuring the Totalizer59
Simulation60
Parameter Overview with Brief61
Description61
Protecting Settings from Unauthorized Access61
Write Protection Via Write Protection61
Switch61
Operation63
Read Device Locking Status63
Reading Measured Values63
Process Variables63
Totalizer64
Adapting the Measuring Device to the Process65
Conditions65
Performing a Totalizer Reset65
Diagnostics and Troubleshooting67
General Troubleshooting67
Diagnostic Information Via Light Emitting67
Diodes67
Transmitter67
Safety Barrier Promass 10068
Diagnostic Information in Fieldcare68
Diagnostic Options68
Calling up Remedy Information69
Diagnostic Information Via Communication69
Interface69
Reading out Diagnostic Information69
Configuring Error Response Mode70
Adapting the Diagnostic Information70
Adapting the Diagnostic Behavior70
Overview of Diagnostic Information71
Pending Diagnostic Events73
Diagnostic List73
Event Logbook74
Event History74
Filtering the Event Logbook74
Overview of Information Events74
12.10 Resetting the Measuring Device75
12.11 Device Information75
12.12 Firmware History76
Maintenance77
Maintenance Tasks77
Exterior Cleaning77
Interior Cleaning77
Measuring and Test Equipment77
Endress+Hauser Services77
Repair78
General Notes78
Repair and Conversion Concept78
Notes for Repair and Conversion78
Spare Parts78
Endress+Hauser Services78
Return78
Disposal79
Removing the Measuring Device79
Disposing of the Measuring Device79
Accessories80
Device-Specific Accessories80
For the Sensor80
Communication-Specific Accessories80
Service-Specific Accessories81
System Components81
Technical Data82
Application82
Function and System Design82
Input83
Output84
Power Supply86
Performance Characteristics87
Installation91
Environment91
Process92
16.10 Mechanical Construction95
16.11 Human Interface97
16.12 Certificates and Approvals98
16.13 Application Packages100
16.14 Accessories101
16.15 Supplementary Documentation101
Index103

Endress+Hauser Proline Promass E 100 - Device Operation and Configuration

Table of Contents

Other manuals for Endress+Hauser Proline Promass E 100

Related product manuals