FAAC A952 - Page 3

A952 1 532310 - Rev.A
CONTENTS
1. INTRODUCTION TO THE INSTRUCTIONS MANUAL ..... 3
1.1 Safety warnings for the installer ....................... 3
1.2 Meaning of the symbols used ......................... 3
1.3 Protection against door movement hazards ............ 3
2. A952................................................... 4
2.1 Storage .............................................. 4
2.2 Unpacking and handling .............................. 4
2.3 Product identification and warning labels .............. 5
2.4 Intended use ......................................... 6
2.5 Application limits .................................... 6
2.6 Unauthorised use .................................... 6
2.7 Emergency Use ....................................... 7
2.8 Manual operation .................................... 7
2.9 Technical characteristics .............................. 8
Dimensions ............................................ 8
2.10 Weight and width limits ............................. 9
Architrave mounted .................................... 9
Leaf mounted ......................................... 11
2.11 Maximum speed limits ............................. 12
2.12 Component identification ........................... 13
2.13 Installation components ............................ 14
3. MECHANICAL INSTALLATION ......................... 15
3.1 Tools required ....................................... 15
3.2 Installation instructions .............................. 16
Permissible substrates................................. 16
Substrate condition ................................... 16
Information on the types of anchors .................... 17
3.3 Fixing the support plate ............................. 18
3.4 Types of installation ................................. 19
3.5 Installing the gearmotor ............................. 27
3.6 Cable routing from the board side .................... 29
3.7 Cable routing from the motor side .................... 30
3.8 Installing the electronics assembly ................... 31
3.9 Installing the shoe arm .............................. 33
3.10 Installing the articulated arm ....................... 36
3.11 Removing the spring preload screw.................. 39
3.12 Adjusting the spring ................................ 40
3.13 Adjusting the spring movement in the absence of power 41
3.14 Adjusting the integrated mechanical opening stop ... 43
3.15 Installing the side covers ............................ 44
3.16 Installing the side functions selector ................. 44
3.17 Preparing the side cable routing opening ............ 45
3.18 Connecting the mains power cable .................. 45
4. ELECTRONIC INSTALLATION .......................... 46
4.1 Electronics assembly ................................. 46
Components .......................................... 46
4.2 Connections ........................................ 47
Control devices ....................................... 47
Outputs .............................................. 47
Lock .................................................. 48
Accessories power supply .............................. 48
Bus ................................................... 48
Canbus ............................................... 48
Not Aus ............................................... 48
Radio/decoder board .................................. 48
Battery ............................................... 48
5. OPERATING MODE .................................... 49
6. CONFIGURABLE INPUTS .............................. 49
RESET input ........................................... 50
7. CONFIGURABLE OUTPUTS ............................ 52
8. STARTUP ............................................ 53
8.1 Setting up the display ............................... 53
8.2 Program the A952 ................................... 53
8.3 On board programming .............................. 53
Accessing programming mode ......................... 53
Modifying the programming .......................... 53
Exiting programming mode ........................... 53
8.4 SETUP .............................................. 57
8.5 RESET .............................................. 57
8.6 Restoring factory settings ............................ 57
9. COMMISSIONING ..................................... 58
9.1 Classification DIN 18650-1 ........................... 58
9.2 Final checks ......................................... 59
9.3 Final operations ..................................... 59
10. ACCESSORIES ....................................... 60
10.1 BUS 2easy Devices .................................. 60
Connection ........................................... 60
BUS 2easy control devices ............................. 60
BUS 2easy device registration .......................... 60
Checking registered devices ........................... 60
10.2 Battery kit ......................................... 61
10.3 Safety sensors
XPB ON , XPB SCAN , XPB SCAN 3D ........ 63
10.4 Lock ............................................... 64
10.5 Simply Connect .................................... 64
10.6 Casing for double leaf applications .................. 65