FAAC A952 - Page 64

To Next Page

To Previous Page

A952 62 532310 - Rev.A

6. Install the press-on front cover and fasten it using

the 4 screws.

7. Plug the connector into the E952CL board.

Main Page

1. INTRODUCTION TO THE instructions MANUAL5
- 1.1 Safety warnings for the installer5
  - 1.2 Meaning of the symbols used5
    - 1.3 Protection against door movement hazards5
      - 2. A9526
        2.1 Storage6
        2.2 Unpacking and handling6
        2.3 Product identification and warning labels7
        2.4 Intended use8
        2.5 Application limits8
        2.6 Unauthorised use8
        2.7 Emergency Use9
        2.8 Manual operation9
        2.9 Technical characteristics10
        Dimensions10
        2.10 Weight and width limits11
        Architrave mounted11
        Leaf mounted13
        2.11 Maximum speed limits14
        2.12 Component identification15
        2.13 Installation components16
        3. Mechanical installation17
        3.1 Tools required17
        3.2 Installation instructions18
        Permissible substrates18
        Substrate condition18
        Information on the types of anchors19
        3.3 Fixing the support plate20
        3.4 Types of installation21
        3.5 Installing the gearmotor29
        3.6 Cable routing from the board side31
        3.7 Cable routing from the motor side32
        3.8 Installing the electronics assembly33
        3.9 Installing the shoe arm35
        3.10 Installing the articulated arm38
        3.11 Removing the spring preload screw41
        3.12 Adjusting the spring42
        3.13 Adjusting the spring movement in the absence of power43
        3.14 Adjusting the integrated mechanical opening stop45
        3.15 Installing the side covers46
        3.16 Installing the side functions selector46
        3.17 Preparing the side cable routing opening47
        3.18 Connecting the mains power cable47
        4. Electronic installation48
        4.1 Electronics assembly48
        Components48
        4.2 Connections49
        Control devices49
        Outputs49
        Lock50
        Accessories power supply50
        Bus50
        Canbus50
        Not Aus50
        Radio/decoder board50
        Battery50
        5. Operating mode51
        6. Configurable inputs51
        RESET input52
        7. Configurable outputs54
        8. START-UP55
        8.1 Setting up the display55
        8.2 Program the A95255
        8.3 On board programming55
        Accessing programming mode55
        Modifying the programming55
        Exiting programming mode55
        8.4 SETUP59
        8.5 RESET59
        8.6 Restoring factory settings59
        9. Commissioning60
        9.1 Classification DIN 18650-160
        9.2 Final checks61
        9.3 Final operations61
        10. Accessories62
        10.1 BUS 2easy Devices62
        Connection62
        BUS 2easy control devices62
        BUS 2easy device registration62
        Checking registered devices62
        10.2 Battery kit63
        10.3 Safety sensors XPB ON , XPB SCAN , XPB SCAN 3D65
        10.4 Lock66
        10.5 Simply Connect66
        10.6 Casing for double leaf applications67
        11. LK EVO68
        12. KS EVO71
        13. KP EVO72
        KP EVO lock device72
        Home page73
        RESET - Block/Release73
        PASSWORD (PSW)73
        MODFUN73
        MENU 74
        Menu 1 language77
        Menu 2 Programming77
        Menu 5 Counters79
        Menu 6 Date / Time79
        Menu 7 TIMER79
        Menu 8 Password80
        Menu 9 Info80
        14. Intercom81
        14.1 Intermode82
        14.2 Interlock82
        Interlock without memory83
        Interlock with memory83
        14.3 2 Leaves83
        14.4 2 Leaves + Interlock83
        15. Upload / Download84
        AutoUpdate84
        Upload/Download Menu84
        16. DIAGNOSTICS85
        16.1 Checking the LEDs85
        Board E952IO85
        16.2 Inputs and outputs status check85
        16.3 Automation status check86
        16.4 Other board data86
        16.5 Firmware versions86
        16.6 Errors and Warnings86
        17. MAINTENANCE91
        17.1 Routine maintenance91
 1 BASIC Programming56
 1 Installation on architrave with an articulated arm (t=3)22
 2 Installation on architrave with a short shoe arm (t=2)23
 3 Installation on architrave with a standard shoe arm (t=2)24
 4 Installation on architrave with a short shoe arm (t=1)25
 5 Installation on architrave with a standard shoe arm (t=1)26
 6 Installation on leaf with an articulated arm (t=3)27
 7 Installation on leaf with an standard shoe arm (t=2)28

FAAC A952 - Page 64

Table of Contents

Related product manuals