EasyManuals Logo

Fujitsu M10 User Manual

Fujitsu M10
374 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #245 background imageLoading...
Page #245 background image
Table
8-2
  
Relationship
between
the
CPU
configuration
and
firmware
update
(continued)
CPU
configuration
of
the
physical
partition
before
addition
CPU
configuration
of
the
chassis
to
be
added
XCP
firmware/Oracle
Solaris
*1
For
XCP
firmware
versions
and
Oracle
Solaris
versions
that
support
a
system
in
which
the
SPARC64
X+
processor
is
mounted,
see
the
following:
"1.6
System
Configuration
and
Software
Conditions
for
Configuring
Physical
Partitions"
in
the
Fujitsu
M10/SPARC
M10
Systems
Domain
Configuration
Guide
and
the
Fujitsu
M10/
SPARC
M10
Systems
Product
Notes
for
the
latest
XCP
version.
*2
Executing
the
addfru
command
for
installation
automatically
updates
firmware
to
match
firmware
versions.
The
update
matches
the
version
on
the
master
XSCF,
so
we
recommend
updating
XCP
on
the
master
XSCF
to
the
latest
version
in
advance.
Note
-
When
using
the
dynamic
reconfiguration
function
for
the
physical
partition
(PPAR
DR),
check
the
contents
of
"2.5
Dynamic
Reconfiguration
Conditions
and
Settings"
in
the
Fujitsu
M10/SPARC
M10
Systems
Domain
Configuration
Guide
beforehand.
Important
-
Be
sure
to
save
the
logical
domain
configuration
information
before
changing
the
PPAR
DR
mode
setting.
When
executing
the
setpparmode
command
to
change
the
PPAR
DR
mode
setting
from
"disable"
to
"enable"
or
vice
versa,
you
must
reset
the
physical
partition
to
reflect
the
setting.
This
reset
restores
the
logical
domain
configuration
information
to
factory-default.
Since
the
logical
domain
configuration
information
that
has
been
saved
beforehand
is
required
for
reconfiguration
of
the
logical
domain,
be
sure
to
save
the
data
before
changing
the
PPAR
DR
mode
setting.
For
details
on
how
to
save
and
restore
logical
domain
configuration
information,
see
"1.7.3
How
to
save/restore
the
logical
domain
configuration
information
and
the
OpenBoot
PROM
environment
variable"
in
the
PCI
Expansion
Unit
for
Fujitsu
M
10/SPARC
M10
Systems
Service
Manual.
Notes
on
use
of
dynamic
reconfiguration
(DR)
for
the
physical
partition
â– 
When
incorporat ing
a
system
board
(PSB)
into
a
physical
partition
with
the
addboard
command
The
addboard
command
with
the
-c
configure
option
specified
cannot
incorporate
a
system
board
(PSB)
into
a
physical
partition
where
the
PPAR
DR
function
is
disabled.
Execute
the
setpparmode
command
beforehand
to
set
the
PPAR
DR
setting
to
"on".
â– 
When
adding
a
system
board
(PSB)
on
which
the
SPARC64
X
processor
is
mounted
in
auto
mode
When
the
CPU
operational
mode
is
set
to
"auto"
mode,
an
attempt
to
add
a
SPARC64
X-mounted
system
board
(PSB)
to
a
SPARC64
X+-mounted
system
by
using
dynamic
reconfiguration
(DR)
fails
because
SPARC64
X+
functions
are
being
used
for
operation.
When
adding
the
system
board
by
using
dynamic
reconfiguration
(DR),
set
the
CPU
operational
mode
to
"compatible"
mode
beforehand.
For
details
on
the
change
procedure,
see
"2.6.2
CPU
operational
mode
settings"
Chapter
8
 
Before
Installing/Removing
a
System
with
a
Building
Block
Configuration 231

Table of Contents

Other manuals for Fujitsu M10

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu M10 and is the answer not in the manual?

Fujitsu M10 Specifications

General IconGeneral
BrandFujitsu
ModelM10
CategoryServer
LanguageEnglish

Related product manuals