FUTABA T16IZ SUPER

180
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ųƌƗƆƋŃƗƕƌƐŃŋūƒƙƈƕƌƑƊŃƓƌƗƆƋŏŃƋƌƊƋŃƓƌƗƆƋŏŃƏƒƚŃƓƌƗƆƋŌ
7KHKRYHULQJSLWFKORZSLWFKDQGKLJKSLWFKWULPVHWXSVFUHHQFDQEHFDOOHGIURPWKH3LWFKFXUYHVHWXS
screen.
Hoveringpitchtrim
setting
Low/highpitchtrim
setting
ūƒƙƈƕƌƑƊŃƓƌƗƆƋŃƗƕƌƐ
The Hovering Pitch trim function trims the pitch
QHDUWKHKRYHULQJSRLQW1RUPDOO\LWLVXVHGZLWK
the hovering condition. The hovering pitch can be
¿QHWXQHGIRUFKDQJHVLQURWRUVSHHGDFFRPSDQ\LQJ
FKDQJHVLQWHPSHUDWXUHKXPLGLW\DQGRWKHUÀLJKW
FRQGLWLRQV$GMXVWWKHKRYHULQJSLWFKVRWKDW
rotor speed is constant. This function can be used
WRJHWKHUZLWKWKHKRYHULQJ7KURWWOH7ULPIXQFWLRQ
for more delicate operation.
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇ
ŏ:KHQXVLQJRQO\WKHKRYHULQJQRUPDO
condition, switch the group mode to the
single mode (initial setting) before setting.
ŏ7DS>,1+@21LVGLVSOD\HG
ŏ6HOHFWWKHDGMXVWPHQWNQRE
Selection example: LD
ŏ7KHWULPRSHUDWLRQPRGH0RGH&HQWHU
Normal) can be selected.
Center mode: Maximum amount of change
near center by center trim operation
(recommended)
Normal mode: Normal trim (parallel
movement trim) operation. The advantage
of using this mode is that the hovering pitch
can be adjusted without changing the
curve.
ŏ7ULPDGMXVWPHQWUDQJH5DQJHVHWWLQJ
When this value is made small, trim can only
be used near the center.
ŏ7KHWULPUDWHFDQEHDGMXVWHGDQGWKH
operation direction can be changed.
ūƌƊƋŃųƌƗƆƋŒůƒƚŃųƌƗƆƋŃŷƕƌƐ
+LJK3LWFK/RZ3LWFK7ULPLVWKHSLWFKVHUYRKLJK
VLGHDQGORZVLGHWULPIXQFWLRQ
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇ
ŏ:KHQVHWWLQJWKHDGMXVWPHQWNQREVFRPPRQ
to all the conditions, set them in the group
mode.
ŏ7DS>,1+@21LVGLVSOD\HG
ŏ6HOHFWWKHDGMXVWPHQWNQREV
Selection example: LS (high side), RS (low
side)
ŏ7KHWULPUDWHFDQEHDGMXVWHGDQGWKH
operation direction can be changed.
ŏ7ULPDFWVDVKLJKVLGHRUORZVLGHWULPZLWKWKH
center as the standard.
ŏ5HWXUQWR0RGHOPHQX