FUTABA T16SZ

140
＜ Modelmenu(Airplane/Glider/MulticopterFunctions) ＞
RUDDER2
RUDDER
RUDDER
V-TAIL
RUDDER2
Winglet
RUDDER1
Winglet
atFlyingwing
atFlyingwing
() ()
AIL3
AIL3
(ChipAileron)
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
Rudder →Aileron
[Corresponding model type]:
Airplane/glider, general
This function is used when you want to mix
the ailerons with rudder operation. It is used
when rudder is applied during roll maneuvers,
knife edge, etc. of stunt planes. It can be used to
bank scale models, large models, etc. like a full
size plane.
ŏ$PL[LQJFXUYHFDQEHVHW
ŏ0L[LQJGXULQJÁLJKWFDQEHWXUQHG212))E\
VHWWLQJDVZLWFK$OZD\V21DW>@VHWWLQJ
ŏ/LQNLQJFDQEHVHW/LQNWKLVPL[WRRWKHUPL[HV
ŏ7KHPL[LQJUDWHFDQEHÀQHWXQHGE\VHWWLQJD95
Setting method
ŏ7DS>,1+@
 21LVGLVSOD\HG
ŏ:KHQVHWWLQJDVZLWFKWDSWRWKH>@LWHP
of the switch and tap the screen to call the
selection screen. Then, select the switch and
VHWLWV21GLUHFWLRQ$OZD\V21DWVHWWLQJ
 )RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQ
PHWKRGVHHEDFNRIWKLVPDQXDO
ŏ:KHQVHWWLQJD95WDSWRWKH)LQHWXQLQJ
LWHPDQGWDSWKHVFUHHQWRFDOOWKH
VHOHFWLRQVFUHHQDQGWKHQVHOHFWWKH957KH
adjustment rate can be set.
7KH95RSHUDWLRQPRGHFDQDOVREHVHW
 )RUDGHVFULSWLRQRIWKHÀQHWXQLQJ95VHWWLQJ
PHWKRGVHHWKHGHVFULSWLRQDWWKHEDFNRI
WKLVPDQXDO
ŏ$PL[LQJFXUYHFDQEHVHW
 )RUDGHVFULSWLRQRIWKHFXUYHVHWWLQJ
PHWKRGVHHWKHEDFNRIWKLVPDQXDO
ŏ:KHQOLQNLQJWDSWKH>/LQN@LWHP21LV
GLVSOD\HG
Currentlyselectedconditionname
● Mixingcurvesetting
(Foradescriptionofthe
settingmethod,seethe
descriptionattheback
ofthismanual.)
Left/rightoverall
adjustmentatRateA
andRateB
Activatethefunctionby
tappingthe[INH].
Conditiongroup/single
modeselection(Gr./Sngl)
TheON/OFFswitchof
mixingischosen.
Finetuning
setting
ŏ6HOHFW>5XGGHUń$LOHURQ@DWWKHPRGHOPHQX
and call the setup screen shown below.
Tosetlinking,tapto
the[OFF]item
ŏ5HWXUQWR0RGHOPHQX