FUTABA T16SZ

48
＜ ModelBasicSettingProcedure ＞
ŏ6ZDVKSODWHFRUUHFWLRQ([FHSW+PRGH
*If any interactions are noticed, for a description of the
linkage correction function, please refer to the SWASH
function.
ŘőŃŷƋƕƒƗƗƏƈŒųƌƗƆƋŃƆƘƕƙƈŃƖƈƗƗƌƑƊ
This function adjusts the throttle or pitch operation
curve in relation to the movement of the throttle stick for
each condition.
Throttle curve setting example!
Call the throttle curve of each condition with the
condition select switch.
ŏ1RUPDOFXUYHDGMXVWPHQW
Normal curve creates a basic throttle curve
FHQWHUHGQHDUKRYHULQJ7KLVFXUYHLVDGMXVWHG
together with the pitch curve (Normal) so that the
HQJLQHVSHHGLVFRQVWDQWDQGXSGRZQFRQWUROLV
easiest.
ŏ,GOHXSFXUYHDGMXVWPHQW
The low side Throttle curve creates a curve
PDWFKHGIRUDHUREDWLFVORRSUROO'HWF
ŏ7KURWWOHKROGFXUYHDGMXVWPHQW
The curve is not used when performing auto rotation
dives.
&RQÀUPWKDWWKHUDWHRIWKHVORZHVWSRVLWLRQRI
WKHVWLFNLVLQLWLDOVHWWLQJ
<Example of pitch curve setting!
Call the pitch curve of each condition with the
condition select switch.
ŏ3LWFKFXUYH1RUPDO
0DNHWKHSLWFKDWKRYHULQJDSSUR[LPDWHO\
º
~6
º
.
Set the pitch at hovering with the stick position at
WKHSRLQWDVWKHVWDQGDUG
*Stability at hovering may be connected to the throttle curve.
Adjustment is easy by using the hovering throttle function
and hovering pitch function together.
ŏ3LWFKFXUYH,GOHXS
The idle up 1 pitch curve function creates a curve
ŗőŃũƘƖƈƏƄƊƈŃƏƌƑƎƄƊƈ
Connect the throttle rudder, aileron, elevator, pitch,
and other servos in accordance with the kit instruction
manual. For a description of the connection method, see
"Servos connection by model type".
Note: The channel assignment of the T16SZ
is different from that of our existing systems.
(The channel assigned to each function can
be checked at the Function menu of the
Linkage menu.)
ŏ,IWKHGLUHFWLRQRIRSHUDWLRQRIWKHVHUYRLV
incorrect, use the Reverse function of the
/LQNDJHPHQX$OVRXVHWKHVZDVK$)5
IXQFWLRQLQRWKHUWKDQWKH+PRGH
ŏ$GMXVWWKHGLUHFWLRQRIRSHUDWLRQRIWKHJ\UR
(Gyro side function)
ŏ&RQQHFWWKHWKURWWOHOLQNDJHVRWKDWWKH
carburetor can fully close at full trim throttle
cut.
ŏ$GMXVWWKHQHXWUDOSRVLWLRQDWWKHOLQNDJH
VLGHDQGÀQHWXQHZLWKWKH6XE7ULPIXQFWLRQ
and End point function (rudder angle
DGMXVWPHQW7RSURWHFWWKHOLQNDJHDOLPLW
position can also be set with the End point
function.