H3C S5130S-EI series User Manual (English)

Other manuals for H3C S5130S-EI series

Manual91 pages

Hardware Information67 pages

Questions and Answers:

E
edwardyoungAug 16, 2025
What to do if there is no display on the configuration terminal of my H3C S5130S-EI?
- A
  Ashley GreenAug 16, 2025
  If you're experiencing no display on the configuration terminal of your H3C Switch, first, make sure the power system is working correctly and that the switch itself is operating as expected. Next, check that the console cable is properly connected. Also, verify that your terminal settings are configured as follows: Baud rate at 9600, Data bits at 8, Parity set to None, Stop bits at 1, and Flow control also set to None. Finally, ensure the console cable is not faulty.
D
Donna AdamsAug 19, 2025
Why is the RPS status LED steady yellow on my H3C S5130S-EI when the system status LED is on?
- M
  Michael TuckerSep 12, 2025
  If the system status LED is on but the RPS status LED is steady yellow on your H3C Switch, verify that the AC power cord is securely connected to the switch, and the AC-input power receptacle on the switch and the connected AC power outlet are in good condition. Also, verify that the AC power source is operating correctly.
J
Joy SolisAug 21, 2025
What to do if there is an AC input failure on my H3C S5130S-EI Switch?
- O
  omorrisonAug 22, 2025
  If the AC input fails on your H3C Switch, start by verifying that the AC power cord is securely connected to the switch, and ensure both the AC-input power receptacle on the switch and the connected AC power outlet are in good working order. Also, confirm that the AC power source is functioning correctly. Finally, check that the switch's operating temperature is within the acceptable range and that the power module has adequate ventilation, as overheating can cause it to shut down as a protective measure.
J
Jennifer AdkinsAug 25, 2025
Why is the display garbled on the configuration terminal of my H3C Switch?
- V
  valerie33Aug 26, 2025
  If you see a garbled display on the configuration terminal of your H3C Switch, check that the terminal settings are configured correctly. Specifically, ensure the Baud rate is set to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None.
D
Daniel ButlerAug 27, 2025
What to do if the RPS status LED is off on my H3C S5130S-EI when the system status LED is on?
- D
  David LopezAug 28, 2025
  If the system status LED is on but the RPS status LED is off on your H3C Switch, verify that the switch is securely connected to the RPS. Also, verify that the RPS is operating correctly.
S
Steven GreerAug 30, 2025
How to troubleshoot a removable power module failure in H3C S5130S-EI Switch?
- M
  Marcus WrightAug 31, 2025
  If you're experiencing a removable power module failure with your H3C Switch, first, ensure that the power module model is the one required for your device. Next, verify that the power module is correctly installed in the switch. Also, check that the switch is operating within the acceptable temperature range. If you need to replace the power module, refer to "Installing and removing power modules".
M
Mary FuentesSep 2, 2025
What to do if there is concurrent RPS and AC inputs failure on my H3C Switch?
- J
  Jamie SampsonSep 3, 2025
  If both RPS and AC inputs fail on your H3C Switch, verify that the AC power cord is securely connected to the switch, and the AC-input power receptacle on the switch and the connected AC power outlet are in good condition. Also, verify that the AC power source is operating correctly. Next, check that the switch is securely connected to the RPS and that the RPS is operating correctly. Finally, ensure the operating temperature of the switch is within the acceptable range, and that the power module has good ventilation, as over-temperature can cause the power module to stop working.
S
Sherri RichardsonSep 6, 2025
What causes RPS DC input failure in H3C S5130S-EI and how to fix it?
- J
  Jordan SimpsonSep 6, 2025
  To address an RPS DC input failure on your H3C Switch, first, verify that the switch is securely connected to the RPS. Then, confirm that the RPS is operating correctly. Also, check that the operating temperature of the switch is within the acceptable range and that the power module has good ventilation, as over-temperature can cause the power module to stop working and enter a protection state.
K
Kristen CareySep 9, 2025
What to do if a removable power module fails on an H3C Switch?
- H
  hmorrowSep 9, 2025
  If you have a removable power module failure on your H3C Switch, take these steps: 1. Check that the AC or DC power cord is correctly connected to the switch. 2. Make sure the power module model is the correct one. 3. Confirm that the power module is correctly installed in the switch. 4. Verify that the switch is operating within the acceptable temperature range.
J
Joel MeyersSep 12, 2025
How to troubleshoot power failure on an H3C S5130S-EI Switch with fixed power modules?
- I
  icarlsonSep 12, 2025
  If your H3C Switch experiences a power failure with fixed power modules, check the following: * Ensure the AC or DC power cord is correctly connected to the switch. * Verify the condition of the AC-input or DC-input power receptacle on the switch and the connected AC or DC power outlet. * Confirm the AC or DC power source is operating correctly. * Check that the switch's operating temperature is within the acceptable range and that the power module has good ventilation. Overheating can cause the power module to stop working.

H3C S5130S-EI series Specifications

General

Series	S5130S-EI
Category	Switch
MAC Address Table Size	16K
VLAN	4K VLANs
Management	Web, CLI, SNMP
Operating Temperature	0°C to 45°C
Storage Temperature	-40°C to 70°C
Operating Humidity	5% to 95% (non-condensing)
Ports	10/100/1000BASE-T ports
Layer Support	Layer 3
Stacking	Supported
Power Supply	AC/DC
PoE	Supported on some models
Dimensions (W x D x H)	440 x 43.6 mm