22
3. OPERATING PROCEDURE [How to Use the Liquid Crystal Display (LCD)]
(1) to (5) : Five Start/Stop Time Patterns
･ START : Starting Time
･ STOP : Stopping Time
･ Y or N : Starts or Stops as scheduled
2.-3. RECORD1, 2 : This function allows for the
capability to record data over a desired time in a day.
To view the recorded data, refer to “5. Operation data
display” on the next page.
㼇㻿㻯㻴㻱㻰㼁㻸㻱㻌㻿㻱㼀㼀㻵㻺㻳㼉
㻝㻥䠖㻜㻣
㻝䠊㻹㻻㻰㻱䠖 㻯㻴㻱㻰㼁㻸㻱
㻿㼀㻭㻾㼀 㻿㼀
㻿
㻻㻼
䠄㻝䠅㻜㻣䠖㻜㻜㻌 㼅 㻞㻜䠖㻜㻜 㻌 㼅
䠄㻞䠅㻜㻜䠖㻜㻜㻌 㻺 㻜㻜䠖㻜㻜㻌 㻺
䠄㻟䠅㻜㻜䠖㻜㻜㻌 㻺 㻜㻜䠖㻜㻜㻌 㻺
䠄㻠䠅㻜㻜䠖㻜㻜㻌 㻺 㻜㻜䠖㻜㻜㻌 㻺
䠄㻡䠅㻜㻜䠖㻜㻜㻌 㻺 㻜㻜䠖㻜㻜㻌 㻺
㻞䠊㻾㻱㻯㻻㻾㻰 㻝䠖 㻝㻜䠖㻜㻜
㻟䠊㻾㻱㻯㻻㻾㻰 㻞䠖 㻝㻥䠖㻜㻜
㻿㻱㼀䠖㻿㼀㻻㻾㻱 㻌㻹㻻㻺䠖㻮㻭㻯㻷
Allows a standard daily scheduling operation.
㼇㻯㻻㻺㼀㻾㻻㻸 㻿㻱㼀㼀㻵㻺㻳㼉
㻝䠊㼀㼅㻼㻼㻱䠖㼂㻭 㼎㼎㼎 㼏㼏㼏
㻞䠊䠬
㻸㻻㻿㻿 䠖 㻖 㻖 㼜 㼟 㼕
㻟䠊䠬㻵
㻯㻭䠖㻖㻖㻖 㻖㻖䠊㻖䡉㻟
䠄㻯㻻㻺㼀㻾㻻㻸䠋㻯㼁㼀㻙 㻵 㻺 㻕
㻠
㻼㻝䠖 㻌 㻝 㻜㻜䠋㻌 㻌 㻤㻣㼜㼟 㼕
㻡
㻼㻞䠖 㻌 㻝 㻜㻜䠋㻌 㻌 㻤㻣㼜㼟 㼕
䠄㼀㻭㻾㻳㻱㼀㻌㻼㻝䠋㻼㻞 㻕
㻢
㼀㻭㻾㻳㻱㼀䠖
㻌㻌 㻥㻤䠋㻌㻌 㻥㻤㼜㼟 㼕
㻣
㼀㻵㻹㻱㻌㻸㻵㻹㻵㼀䠖 㻜㻟㻜㼟
䠄㻼㻞 㻱㻲㻲㻱㻯
ࠥ
㼀㻵㼂㻱㻕
㻤䠊㼀 㻵㻹㻱䠖㻝㻤䠖 㻜㻜 㻞㻞䠖 㻜㻜
㻿㻱㼀䠖㻿㼀㻻㻾㻱 㻌㻹㻻㻺䠖㻮㻭㻯㻷
①② ③
④
⑤
⑥
8. TIME: ⑥ Can set the time to use pressure setting 2.
When set the value properly, ② is indicated in “ S-A”. If
the start and stop time is set at same value, pressure
setting 2 is not in use and ② is indicated in S-1. And
pressure setting 1 and 2 can be changed by external
switch. Set the F018 on digital monitor “2”. (
3.4.2
and 3.4.7)
This function sets the pressures and times for capacity
control. Two different combinations (P1 and P2) of
pressures can be used. Item number with dot “ . ” can
be select from LCD monitor. Item number with a dash “
- “ can be selected from digital monitor. (
3.4)
3
Capacity control
4
Scheduled Operation
1. Type: Indicates the setting data for capacity control
① Type of capacity control (Cannot be changed from
LCD monitor)
Fixed speed type
I: Indicates the standard, 2-step control.
IP: Indicates the motor stop/restart capacity control
to “I”.
Vtype
VA: Indicates motor stop/restart capacity control is
effective.
VB: Indicates motor stop/restart capacity control is
canceled.
② Pressure setting (Cannot be changed from LCD
monitor)
S-1: Indicates pressure setting 1
S-2: Indicates pressure setting 2
EXT: Indicates external pressure setting
S-A : Indicates pressure setting switches by set time
on ⑥.
③ Option condition and setting.
NUL: Indicates no option.
2. - 3. OPTION: Used for options.
4. - 6. Pressure Setting: ④ Indicates cut-in, cut-out
and target pressure setting 1 and 2 can be confirmed.
Target means target pressure for ECOMODE
7. TIME LIMIT (Fixed speed type only)
⑤ Indicates the time limit of load/unload one-cycle
time for ECOMODE. Load/unload one-cycle time
must be 30 seconds or more. (
3.4.8)
The settings can be memorized while the air compressor
is stopped.
IMPORTANT
This illustration indicates a scheduling operation from 7:00 to
20:00. TIME field indicates a current time of 19:07.
1. MODE:
OFF Operates without a schedule.
Schedule Operates according to a daily 24- hour calendar.
When the schedule is selected, the AUTO light comes ON
(glowing) if the time setting is valid and ON (blinking) if the
time setting is invalid. The settings can be memorized
while the air compressor is stopped.
IMPORTANT
To Next Page
Loading...
Need help?
General
