System Options Menu - Continued
65
Default Eng. Code - 4567 Default User Code - 1111 (Irl) 1234 (UK)
Used to select which quick codes are enabled.
Each Quick Code can be individually enabled or disabled. The
User can still access these functions if he/she has been
assigned the User Menu option. Please refer to appendix for a
description of Quick Keys.
Note: Part Set A is normally used for a Night Set and Part Set B is
normally used for a Home Set.
83 QUICK KEY MENU
8311 0#1 - User Log
8312 0#3 - Walk Test
8313 0#4 - Full Set
8314 0#5 - Quick Arm
8315 0#6 - Tog Chime
8316 0#7 - Part Set A
8317 0#8 - Part Set B
8318 0#9 - Bell Test
8321 0*1 - Sms Engs.
8322 0*2 - Sms Log
8323 0*3 - Call PC
8324 0*4 - PC Direct
8325 0*5 - UserChk
8326 0*6 - TmpUser
8327 0*7 - HomeAlone
0#1 - User Log
0#3 - Walk Test
0#4 - Full Set
0#5 - Quick Arm
0#6 - Tog Chime
0#7 - Part Set A
0#8 - Part Set B
0#9 - Bell Test
0*1 - Sms Engs.
0*2 - Sms Log
0*3 - Call PC
0*4 - PC Direct
0*5 - UserChk
0*6 - TmpUser
0*7 - HomeAlone
The User Log is a record of events that can be viewed by the end user. It is limited to
those events that occurred since the system was last armed.
As the end user opens a zone they will briefly hear the buzzer and interior siren, they will
also see the zone description appear on the keypad display. The buzzer and internal
siren will be briefly heard again as the zone is closed.
The user can arm the system with an exit time.
The user can arm the system with zero exit time.
The chime feature can be turned on by pressing 0#6. Pressing 0#6 again will turn off the
chime feature. “Tog” is shorthand for “Toggle”.
The panel can be partially set i.e. those zones excluded from Part Set A will not activate.
The panel can be partially set i.e. those zones excluded from Part Set B will not activate.
The system will systematically sound the buzzer and illuminate the LED’s on the key
pad, then sound the interior siren and finally prompt the user to go outside and sound the
exterior siren and activate the strobe.
The last 7 non-user log events can be sent as a text message by the user to the
installation engineer(s) pre-programmed phone numbers.
The last 7 non-user log events can be sent as a text message by the user to any text
enabled phone. The user will be prompted to key-in the phone number.
The user can call, via the digi modem, a remote PC supporting SmartLink 7. They will be
prompted to key-in the remote location’s phone number.
The user can start a SmartLink 7 session, via connector J5 on the panel.
This is used with the User Alert feature to check that a user is still on the premises.
The user can create a temporary user code that is valid for a limited number of days.
This code may be used by temporary users like tradesmen, cleaners etc.
This enables and disables the HomeAlone timer which is used to generate an event
should a user not unset the panel within a certain time-frame. At the “Home From” time, if
the panel is unset then an event will be generated indicating that the user cannot unset
the panel. The event logged will indicate who did unset the panel. The “Home To” time
indicates the latest time at which the user should unset the panel. If this time is reached
and the required user has not unset the panel then this will be logged indicating that the
user has not checked in on time. If a dialler is attached to the panel then the events
generated can be sent as an SMS message to relevant phones
A typical set-up for a child returning from school... Home From = 16:00, Home To = 16:30
(Monday - Friday)
!
To Next Page
Loading...
Need help?
General
