Programming Menu
Default Eng. Code - 4567 Default User Code - 1111 (Irl) 1234 (UK)
8
2 Devices Menu
1 Service Menu
3 Zone Menu
2 Wired Devices Menu
1 Add & Identify Points
1 Zone Names
5 Default RF System ?
1 Default All ?
2 Default User Codes ?
3 Default Comms ?
1 RF Devices Menu
2 Locate Points
2 Zone Types
3 Remove Points
3 Zone Options
4 Zone Gross & Pulse
5 Zone Hardware
6 Zone Block Assign
7 Technical Zone Options
4 Point Menu
6 Timers Menu
7 Output Menu
Not Applicable
5 Users Menu
1 Point Names
1 Set Time & Date
5 Event Timers
4 Block Timers
1 User Codes
2 Point Types
2 System Timers
2 User Names
3 Point Options
3 Miscellaneous Timers
3 User Options
4 Point Gross & Pulse
5 Point Block Assign
4 Engineer Code
5 User Block Assign
6 User Prox Assign
7 Manufacturer’s Code
1 Never Log
2 Non EOL
1 Zone Name Text
1 Point Name Text
1 Entry Timers
2 Only Log at Setting
3 Single EOL
2 Zone Audio
2 Point Audio
2 Exit Timers
3 Internal Bell Timers
3 Show Open before Set
4 Dual EOL
4 Inhibit Required
5 Point ID
1 RF Device
dd/mm/yy hh:mm
1 Weeks to Service
1 Internal Bell
2 Fire Exit Delay
3 Mains Fault Delay
2 External Bell
3 Strobe Time
4 Entry Time
5 Exit Time
6 Split Entry Time
7 Soak Period
8 Bell Delay
9 Double Knock Reset
0 Double Knock Open
USER OPTIONS
EVENT TIMER TYPES
Full Set User Menu
Unset Manager Menu
Inhibit 24 Hour
Partset A Code & Prox
Partset B
Unused Auto-Arm PGA
Open/Closed Auto-Arm PGB
Home Alone Timed Access
Auto-Activate User Alert
Auto-Arm Full
2 Battery Load Test
2 Colour
4 Replace Battery Pack
4 Live Images
2 Full Set ?
2 Log Menu
1 Unset ?
1 System Overview
4 Default ID Bus ?
3 Quick Arm ?
3 Engineering Tools Menu
4 Part Set A ?
4 Engineer Arm/Disarm
5 Part Set B ?
5 Defaults Menu
6 Firmware Update
7 Voice Demo
8 Remote Service
1 Battery Current Monitor
1 Image Size
3 Charge Battery
3 Number of Pages
1 Test Digi Channels
2 Test Extended Reports
8 Battery Menu
9 Bell Test
4 RF SABB Status
5 RF Wand Status
6 RF Keypad Status
1 RF Device Status
1 RF Zone Status
2 Open Inputs Menu
3 Walk Test Menu
4 Show System Faults
2 RF Keyfob Status
5 Test Comms Menu
6 Test RF Devices
7 Show Software Versions
3 RF Echo Status
1 Add & Identify RF Devices
2 Locate RF Devices
3 Remove RF Devices
4 RF Device Options
5 RF System Options
6 RF Camera Options
Inhibit
Access
Excl. from PG A
Excl. from PG B
Double Knock
Soak
Chime
24 Hour
Perimeter
Inhibit
Excl. from PG A
Excl. from PG B
Soak
Chime
Inhibit
Soak
Silent PA
Inhibit
Soak
Soak
Key Pulse
Inhibit
Soak
24 Hour
Fire Exit Delay
None
Inhibit
Soak
24 Hour
ZONE/POINT TYPES vs OPTIONS
Alarm
Entry / Exit
Panic
Fire
Tamper
Gas
Key
Key Partguard A
Key Partguard B
Fire Exit
Exit Terminator
Line Fault
Fail To Communicate
Technical
Please turn over
for...
8 System Options
Menu &
9 Comms Menu
ZONE & POINT TYPES
Alarm Technical 1
Entry/Exit .. ..
Panic Technical 8
Fire Technical 8
Gas Fire Exit 1
Tamper .. .. ..
Key Fire Exit 12
Line Fault Key Partguard A
Fail to Connect Key PartguardB
Unused Exit Terminator
To use quick codes simply key in the codes indicated to the
left of the items in the menus e.g. Enter keys 31 from the
main menu to access the Zone Names menu.
QUICK CODES
4 External Bell Timers
For adjusting RF-PIR sensitivity,
activating/deactivating the MC’s in
RF-Contact/Sensors, turning on
the “Unset via User-code” feature
on the key-fob, adjusting the RF-
Echo volume, controlling the flash
on the RF-PIRCAM etc.
To Next Page
Loading...
Need help?
General
