Honeywell FMC2000 - Wiring Blocks in the FMC2000

112 pages

Save Page as PDF

To Next Page

To Previous Page

FMC2000 User’s Guide

27.1 Wiring Blocks In The FMC2000

(The schematic below is included inside the FMC2000.)

Main Page

Default Chapter2
- Fcc Information2
- Table of Contents3
1 Special Notes8
- Warnings9
2 Standard Contents10
3 General Information10
- Key Features10
4 Physical Description11
- Rear View and Side View of Enclosure12
- Mounting the FMC200012
- Drilling Chart14
5 Specifications15
6 Charging the Internal Backup Battery16
- Clock Battery16
- Data Protection While Power Is off16
- SD Card16
7 User Interface18
- Status Leds19
- Display19
- Keypad20
- Alarms20
- Preparing the FMC2000 for Data Storage21
8 Operating the FMC200024
- Turning the FMC2000 on24
- Turning the FMC2000 off26
9 Display Information27
- Display Icons28
10 Navigation30
11 Normal Operation Mode Controls31
- Radio Silent (Enable/Disable)31
- Reset31
- Silence Alarm32
- Check (Alarm Details)33
- Monitoring35
- Detail Info35
- Meshguard EC or LEL36
  - Meshguard Router38
12 Configuration39
13 General Settings Menu40
- Basic Settings41
- Date Format42
- Date42
- Time Format43
- Time43
- Language45
- Backlight45
- Instrument Location46
- Serial Number46
- Firmware Version46
- Build Date46
- Build Time46
14 Advanced Settings47
- Basic Password47
- Advanced Password48
- Online Monitors48
- Delete Monitors Configuration49
- Delete Relay Configuration49
- Echoview49
- Alarm Buzzer49
- Alarm Light50
- Backup Configuration50
- Restore Configuration50
- Factory Reset51
15 Wireless Detector Settings51
- Modem ID52
- Location52
- Data Interval52
- Sensor Type53
- Unit53
- Low53
- High53
- Stel53
- Twa54
- Full Scale54
- Drift54
- Reset LEL54
16 Relay Settings55
- Relay Ratings (Resistive)55
- Type56
- Don56
- Dof57
- Lock57
- Vote58
- Num59
- Slave ID59
17 Datalog Settings Menu60
- Datalog60
- Log Interval61
- Log Method61
- SD Card Info62
18 Communications Menu63
- Wireless Modem64
- Ethernet Network67
19 Diagnostic Menu75
- Relay Output Diagnostic75
20 Transferring Data from the SD Card77
21 After Transferring Data from the SD Card79
22 Maintenance81
- Battery Charging & Replacement81
- SD Card Replacement81
- Special Servicing Note82
23 Troubleshooting83
24 Technical Support85
25 Honeywell Analytics Contacts86
26 Appendix A: Wiring the FMC200088
- DC Wiring88
- AC Wiring88
- External Alarms89
- Wiring Blocks in the FMC200090
- Relay Electrical Drawing91
- Checking Relay Continuity92
27 Appendix B: Wiring to External Alarms93
- Power Supply Connections93
- Dry Contact Operation94
28 Appendix C: Connecting RS485 (Modbus)94
29 Appendix D: Connecting Ethernet95
30 Appendix E: Connecting to a Light/Alarm Bar96
32 Appendix G: Modbus Protocol for the FMC200097
31 Appendix F: Formatting an SD Card for FAT3297
- Formatting an SD Card97
Appendix G: Modbus Protocol for the FMC2000103
- Overview103
- Communications Settings103
- Message Frame/Communication Procedure104
- Registers Table105

Honeywell FMC2000 - Wiring Blocks in the FMC2000

Table of Contents

Related product manuals