Honeywell FMC2000 - Relay Electrical Drawing

112 pages

Save Page as PDF

To Next Page

To Previous Page

FMC2000 User’s Guide

Explanation of wiring blocks:

27.2 Relay Electrical Drawing

Relay 1 is for

Low Alarm

Relays 2, 3, 4,

and 5 are for

High Alarm

10V output provides

10 VDC @ 2A

RS-485 data output

Main Page

Default Chapter2
- Fcc Information2
- Table of Contents3
1 Special Notes8
- Warnings9
2 Standard Contents10
3 General Information10
- Key Features10
4 Physical Description11
- Rear View and Side View of Enclosure12
- Mounting the FMC200012
- Drilling Chart14
5 Specifications15
6 Charging the Internal Backup Battery16
- Clock Battery16
- Data Protection While Power Is off16
- SD Card16
7 User Interface18
- Status Leds19
- Display19
- Keypad20
- Alarms20
- Preparing the FMC2000 for Data Storage21
8 Operating the FMC200024
- Turning the FMC2000 on24
- Turning the FMC2000 off26
9 Display Information27
- Display Icons28
10 Navigation30
11 Normal Operation Mode Controls31
- Radio Silent (Enable/Disable)31
- Reset31
- Silence Alarm32
- Check (Alarm Details)33
- Monitoring35
- Detail Info35
- Meshguard EC or LEL36
  - Meshguard Router38
12 Configuration39
13 General Settings Menu40
- Basic Settings41
- Date Format42
- Date42
- Time Format43
- Time43
- Language45
- Backlight45
- Instrument Location46
- Serial Number46
- Firmware Version46
- Build Date46
- Build Time46
14 Advanced Settings47
- Basic Password47
- Advanced Password48
- Online Monitors48
- Delete Monitors Configuration49
- Delete Relay Configuration49
- Echoview49
- Alarm Buzzer49
- Alarm Light50
- Backup Configuration50
- Restore Configuration50
- Factory Reset51
15 Wireless Detector Settings51
- Modem ID52
- Location52
- Data Interval52
- Sensor Type53
- Unit53
- Low53
- High53
- Stel53
- Twa54
- Full Scale54
- Drift54
- Reset LEL54
16 Relay Settings55
- Relay Ratings (Resistive)55
- Type56
- Don56
- Dof57
- Lock57
- Vote58
- Num59
- Slave ID59
17 Datalog Settings Menu60
- Datalog60
- Log Interval61
- Log Method61
- SD Card Info62
18 Communications Menu63
- Wireless Modem64
- Ethernet Network67
19 Diagnostic Menu75
- Relay Output Diagnostic75
20 Transferring Data from the SD Card77
21 After Transferring Data from the SD Card79
22 Maintenance81
- Battery Charging & Replacement81
- SD Card Replacement81
- Special Servicing Note82
23 Troubleshooting83
24 Technical Support85
25 Honeywell Analytics Contacts86
26 Appendix A: Wiring the FMC200088
- DC Wiring88
- AC Wiring88
- External Alarms89
- Wiring Blocks in the FMC200090
- Relay Electrical Drawing91
- Checking Relay Continuity92
27 Appendix B: Wiring to External Alarms93
- Power Supply Connections93
- Dry Contact Operation94
28 Appendix C: Connecting RS485 (Modbus)94
29 Appendix D: Connecting Ethernet95
30 Appendix E: Connecting to a Light/Alarm Bar96
32 Appendix G: Modbus Protocol for the FMC200097
31 Appendix F: Formatting an SD Card for FAT3297
- Formatting an SD Card97
Appendix G: Modbus Protocol for the FMC2000103
- Overview103
- Communications Settings103
- Message Frame/Communication Procedure104
- Registers Table105

Honeywell FMC2000 - Relay Electrical Drawing

Table of Contents

Related product manuals