6 Notifier SLC Wiring Manual — P/N 51253:U9 12/3/2021
Table of Contents
5.3.1: How an Isolator Base Works ................................................................................................................................................................31
5.4: NFPA Class B SLC Using Isolator Modules ...................................................................................................................................................33
5.5: NFPA Class A SLC Using Isolator Modules ...................................................................................................................................................35
5.6: NFPA Class X SLC Using an Isolating Device ...............................................................................................................................................36
Section 6: Monitor Modules............................................................................................................................................ 37
6.1: Description.......................................................................................................................................................................................................37
6.1.1: Addressable Monitor Module...............................................................................................................................................................37
6.1.2: Zone Interface Module .........................................................................................................................................................................37
6.1.3: Miniature Monitor Module...................................................................................................................................................................38
6.1.4: FMM-4-20 4-20mA Monitor Module ..................................................................................................................................................38
6.2: Setting an SLC Address for a Module .............................................................................................................................................................38
6.3: NFPA Class B IDC Using Monitor Modules...................................................................................................................................................39
6.4: NFPA Class A IDC Using Monitor Modules ...................................................................................................................................................40
6.5: NFPA Class B IDC Using Zone Interface Modules.........................................................................................................................................41
6.6: NFPA Class A IDC Using Zone Interface Modules.........................................................................................................................................42
Section 7: Control Modules ............................................................................................................................................ 44
7.1: Description.......................................................................................................................................................................................................44
7.1.1: Setting an SLC Address........................................................................................................................................................................44
7.2: Wiring a NAC with Addressable Control Modules .........................................................................................................................................44
7.2.1: Wiring a Solenoid with the FCM-1-REL .............................................................................................................................................45
7.3: Wiring a Class B NAC (Two-Wire) with Addressable Control Modules ........................................................................................................45
7.4: Wiring a Class A NAC (Four-Wire) with Addressable Control Modules........................................................................................................46
7.5: Connecting a Releasing Device to the Addressable Control Module..............................................................................................................47
Section 8: Relay Module ................................................................................................................................................. 49
8.1: Description.......................................................................................................................................................................................................49
8.1.1: Setting an SLC Address........................................................................................................................................................................49
8.2: Wiring the Addressable Relay Module (Form-C Relay) .................................................................................................................................49
Section 9: Multiple Input/Output Modules..................................................................................................................... 50
9.1: Description.......................................................................................................................................................................................................50
9.1.1: FDM-1 ..................................................................................................................................................................................................50
9.1.2: FDRM-1................................................................................................................................................................................................50
9.2: Setting the SLC Address..................................................................................................................................................................................50
9.2.1: FDM-1 ..................................................................................................................................................................................................50
9.2.2: FDRM-1................................................................................................................................................................................................50
9.3: Wiring the Dual Monitor Module ....................................................................................................................................................................50
9.4: Wiring the Addressable Dual Monitor/Dual Relay Module ............................................................................................................................51
9.5: NFPA Class B IDC Wiring Using Dual Monitor Modules ..............................................................................................................................51
Section 10: Intelligent Detectors, Intelligent Detector Bases, and Wireless Gateway.............................................. 53
10.1: Description.....................................................................................................................................................................................................53
10.1.1: Intelligent Detector Bases...................................................................................................................................................................53
10.1.2: Intelligent Aspiration Detectors..........................................................................................................................................................53
10.1.3: Wireless Gateway ...............................................................................................................................................................................54
10.2: Wiring a Detector Base ..................................................................................................................................................................................54
10.3: Wiring an Isolator Base .................................................................................................................................................................................56
10.4: Wiring a Relay Base ......................................................................................................................................................................................56
10.5: Wiring a Sounder Base ..................................................................................................................................................................................57
10.6: Wiring and Programming Aspiration Detectors ............................................................................................................................................58
10.7: Wiring the FWSG(A) ....................................................................................................................................................................................62
10.7.1: SLC Connections ................................................................................................................................................................................62
10.8: Power Connections: Powered by the SLC.....................................................................................................................................................63
10.8.1: Power Connections: External, Regulated +24 VDC Power Source ..................................................................................................64
Section 11: Addressable Manual Pull Stations............................................................................................................. 65
11.1: Description.....................................................................................................................................................................................................65
11.1.1: Setting an SLC address .......................................................................................................................................................................65
11.2: Wiring a Manual Pull Station.........................................................................................................................................................................65
Appendix A: Power Considerations .............................................................................................................................. 66
A.1: Supplying Power to 24 VDC Detectors and NACs ........................................................................................................................................66
A.2: Supervising 24 VDC Power............................................................................................................................................................................66
To Next Page
Loading...
Need help?
General
