HP 10000 G2 Series

To Next Page

To Previous Page

Cable Management Tray kit 38

Install the cable management tray on top of the rack, using the same two screws you removed in step

4. Route the cables through the cable management tray.

Main Page

Default Chapter1
- Installation Guide1
- Table of Contents3
About this Guide7
- Rack Options Installation Guide7
- Important Safety Information7
- Additional Rack Considerations7
Rack Options9
- Ordering Rack Options9
100 Kilo Sliding Shelf Kit11
- About this Device11
  - Kit Contents11
  - Required Tools11
- Preparing the Sliding Shelf Rail Assemblies for Installation11
- Installing the Sliding Shelf Rail Assemblies12
- Installing the Sliding Shelf14
- Using the 100 Kilo Sliding Shelf16
Airflow Optimization Kit17
- About this Device17
  - Kit Contents17
  - Required Tools17
- Installing Foam Rail Gaskets17
  - Installing Foam Rail Gaskets between Racks18
- Installing the Floor Gasket20
Ballast Kit22
- About this Device22
  - Kit Contents22
  - Required Tools22
- Installing the Ballast Kit22
Baying Kit25
- About this Device25
  - Kit Contents25
  - Required Tool25
- Installing the Baying Kit25
Cable Management Bracket Kit28
- About this Device28
  - Kit Contents28
  - Required Tools28
- Installing the 1U Cable Management Bracket29
- Installing the 2U Cable Management Bracket30
- Installing the Cable Management D-Ring Bracket30
  - Front Mount31
  - Side Mount32
- Installing the Cross-Over Bracket32
- Installing the Hook-And-Loop Cabling Straps34
Cable Management Tray Kit36
- About this Device36
  - Kit Contents36
  - Required Tool36
- Installing the Cable Management Tray37
- Installing the Cable Management Inner and Outer Trays39
- Ground Bonding Stud Location41
Fan (110V/220V) Kit42
- About this Device42
  - Kit Contents42
  - Required Tools42
- Installing the Fan42
Filler Panel Kit45
- About this Device45
  - Kit Contents45
  - Required Tools45
- Installing the Filler Panel45
Front Door Kit46
- About this Device46
  - Kit Contents46
  - Required Tools46
- Installing the Hinge Brackets and Lock Catches47
- Installing the Front Door48
Ground Bonding Kit49
- About this Device49
  - Kit Contents49
  - Required Tools49
- Installing the Ground Bonding Rack Option Kit on HP 10000 G2 Series Racks49
- Installing the Ground Bonding Rack Option Kit on HP 10000 Series Racks62
  - Installing the Ground Bonding Rack Option Kit on HP 10000 Series Rack Side Panels67
  - Installing the Ground Bonding Rack Option Kit on HP 10000 Series Rack Fan Kits67
Heavy Duty Stabilizer Kit69
- About this Device69
  - Kit Contents69
  - Required Tools69
- Installing the Rack Stabilizer Option Kit69
Hook-And-Loop Cabling Strap Clip Kit72
- About this Device72
  - Kit Contents72
  - Required Tools72
- Installing the Hook-And-Loop Cabling Strap Clips73
Light Kit76
- About this Device76
  - Kit Contents76
  - Required Tool76
- Important Safety Information76
- Installing the 110V/220V Light77
- Operating the 110V/220V Light79
- Connecting the Power Cord to the 110V/220V Light79
- Connecting Devices to the 110V/220V Light79
- HP 110V/220V Light Kit Specifications80
- F14W/133-T8 Fluorescent Lamp Specifications81
- Material Disposal82
Mini Stabilizer Kit83
- About this Device83
  - Kit Contents83
  - Required Tools83
- Installing the Stabilizer83
Rack Air Duct Kit86
- About this Kit86
  - Kit Contents86
  - Required Tools87
- Installation Video88
- Installing the Top Exhaust Retrofit Kit88
- Installing the Top Exhaust Extension Kit93
- Baying Options103
Rear Extension Kit105
- About this Device105
  - Kit Contents105
  - Required Tools105
- Removing the Rear Doors105
- Installing the Rear Extension Assembly107
- Installing the Rear Doors109
- Installing the Cable Management Brackets110
Server/Utility Shelf Kit112
- About this Device112
  - Kit Contents112
  - Required Tools112
- Installing the Server/Utility Shelf112
Side Panel Kit116
- About this Device116
  - Kit Contents116
  - Required Tools116
- Installing the Side Panels117
Tie-Down Kit119
- About this Device119
- 1200 MM Full Frame Rack Tie-Down Kit121
Vertical PDU Mounting Kit124
- About this Device124
  - Kit Contents124
  - Required Tools124
- Installing the Vertical PDU Mounting Kit124
Electrostatic Discharge126
- Preventing Electrostatic Discharge126
- Grounding Methods to Prevent Electrostatic Discharge126
Support and Other Resources127
- Before You Contact HP127
- HP Contact Information127
Acronyms and Abbreviations128
Documentation Feedback129

HP 10000 G2 Series - Page 38

Table of Contents

Other manuals for HP 10000 G2 Series

Related product manuals