Hypertherm HyPerformance Plasma HPR800XD User Manual

OperatiOn
HPR800XD Auto Gas – 806500 4-49
Metric
English
Select
Gases
Set
Preflow
Set
Cutflow
Minimum
Clearance
Equivalent
Material
Thickness
Torch-to-Work
Distance
Cutting
Speed
Initial Pierce
Height
Pierce Delay
Time
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
mm mm Range (mm) mm/m mm Factor % Seconds
O
2
Air 15
23
84
21
2.0
3 2.5 – 8.6 6505 5.0
200
0.1
4
2.8 – 8.6
5550
5.6
0.2
5 4795
0.3
6 4035
15
8
3.0 – 8.6
3360
6.0
10 2680
12 3.3 – 8.6 2200 6.6 0.5
15
3.8 – 8.6
1665
7.6
0.7
20 1050 1.0
25 4.0 – 8.6 550 190 1.8
33
32
*
4.5 – 8.6
375 10.2 220 4.0
38 255 Edge start
Select
Gases
Set
Preflow
Set
Cutflow
Minimum
Clearance
Equivalent
Material
Thickness
Torch-to-Work
Distance
Cutting
Speed
Initial Pierce
Height
Pierce Delay
Time
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
in in Range (in) ipm in Factor % Seconds
O
2
Air 15
23
84
21
0.08
0.135 0.10 – 0.34 240 0.20
200
0.1
3/16
0.11 – 0.34
190
0.22
0.2
1/4 150
0.3
15
5/16
0.12 – 0.34
132
0.24
3/8 110
1/2 0.13 – 0.34 80 0.26 0.5
5/8
0.15 – 0.34
60
0.30
0.7
3/4 45 1.0
1 0.16 – 0.34 20 190 1.8
33
1-1/4*
0.18 – 0.34
15 0.40 220 4.0
1-1/2 10 Edge start
Mild steel bevel cutting
O
2
Plasma / Air Shield
130 A
Flow rates – lpm/scfh
O
2
Air
Preflow 0 / 0 64 / 135
Cutflow 33 / 70 45 / 96
220742
220637
220649220740 220179220646
Note: Bevel angle range is 0° to 45°.
220700
Select
Gases
Set
Preflow
Set
Cutflow
Amperage
Torch-to-Work
Distance
Marking
Speed
Arc
Voltage
Amps mm in mm/m ipm Volts
N
2
N
2
10 10 10 10 15 2.5 0.10 6350 250 130
Ar Air 50 10 50 10 15 3.0 0.12 2540 100 75
Marking
* Suggestions for piercing 32 mm (1-1/4 in) mild steel: 1. Turn preflow on during IHS, 2. Use ohmic contact during IHS,
3. Use pierce complete when piercing.

Hypertherm HyPerformance Plasma HPR800XD Specifications

General

Brand	Hypertherm
Model	HyPerformance Plasma HPR800XD
Category	Cutter
Language	English