Hypertherm HyPerformance Plasma HPR800XD User Manual

7-28
4 3 2 1
1
A
4 3 2
A
B
C
D
B
C
D
ELEC SCH:HPR400XD POWER SUPPLY W/AUTO
D
013381
SHEET 24 OF 24
Unit 1
and/or EdgePro Module(s)
ArcGlide THC
141030
CONTROL BOARD
1 2 3 4
S301
12
J300
34 3 2 14
J303A J1
ArcGlide Ethernet Cable
Unit 2
Unit 3
Unit 4
CNC Interface Cable
Serial ID
Dipswitch
Machine Motion
Jumper Block
J10 4
21
J105
1 2
Notes:
1) For the 141030 control board, set Serial ID (S301), and Machine Motion (J300) as shown.
Jumpers J104 and J105 should be installed.
All 141030 DIPSWITCH and jumper settings are the same; serial IDs are determined
by the 141131 board setting.
2) For a single system installation, set SW1 on the 141131 board as shown in Unit 1.
3) For a two system installation, set SW1 on the 141131 boards as shown in Units 1 through 2.
4) For a three system installation, set SW1 on the 141131 boards as shown in Units 1 through 3.
5) For a four system installation, set SW1 on the 141131 boards as shown in Units 1 through 4.
Optional ArcGlide/EdgePro Multi-System Interface
5 6 7 8
ON
J303B J5
141131
ETHERNET
INTERFACE
BOARD
0
7
1
5
4
6
2
3
SW1
UNIT ADDRESS
141030
CONTROL BOARD
1 2 3 4
S301
12
J300
34 3 2 14
J303A J1
Serial ID
Dipswitch
Machine Motion
Jumper Block
J10 4
21
J105
1 2
5 6 7 8
ON
J303B J5
0
7
1
5
4
6
2
3
SW1
UNIT ADDRESS
141030
CONTROL BOARD
1 2 3 4
S301
12
J300
34 3 2 14
J303A J1
Serial ID
Dipswitch
Machine Motion
Jumper Block
J10 4
21
J105
1 2
5 6 7 8
ON
J303B J5
0
7
1
5
4
6
2
3
SW1
UNIT ADDRESS
141030
CONTROL BOARD
1 2 3 4
S301
12
J300
34 3 2 14
J303A J1
Serial ID
Dipswitch
Machine Motion
Jumper Block
J10 4
21
J105
1 2
5 6 7 8
ON
J303B J5
0
7
1
5
4
6
2
3
SW1
UNIT ADDRESS
CNC Interface Cable CNC Interface Cable CNC Interface Cable
ArcGlide Ethernet Cable
ArcGlide Ethernet Cable ArcGlide Ethernet Cable
HPR PAC
Dry Cutting System
HPR PAC
Dry Cutting System
HPR PAC
Dry Cutting System
HPR PAC
Dry Cutting System
141131
ETHERNET
INTERFACE
BOARD
141131
ETHERNET
INTERFACE
BOARD
141131
ETHERNET
INTERFACE
BOARD
Switch 1 is in the On position
Switches 2-8 are in the Off position
S301
1 2 3 4 5 6 7 8
Dipswitch setting example:
21 3 4
5 6 7 8
ON
ON

Hypertherm HyPerformance Plasma HPR800XD Specifications

General

Brand	Hypertherm
Model	HyPerformance Plasma HPR800XD
Category	Cutter
Language	English