Icom IC-910H - Repeater Operation

34
5
RECEIVE AND TRANSMIT
n Repeater operation
A repeater amplifies received signals and re-transmits
them at a different frequency. When using a repeater,
the transmit frequency is shifted from the receive fre-
quency by an offset frequency.
D Setting the auto repeater range
(U.S.A. and Korea versions only)
The auto repeater function automatically turns ON the
duplex operation with specified shift direction and tone
encoder when the operating frequency is set in the de-
sired frequency range. To activate the auto repeater
function, the following operations are necessary.
q Set one edge frequency of the desired frequency
range.
 • Push[M/S•BAND]toselectthedesiredbandifrequired.
 •Push[FM]toselectFMmodeifrequired.
w Set the desired repeater conditions.
 •Bothone-touchrepeaterandmanualrepeatersetting
are acceptable.
e Push [DN Z] or [Y UP] to select the memory chan-
nel 1.
 •Thememorychannel3or5isalsoacceptable.
r Push [MW 4] for 1 sec. to program the contents into
the memory.
 •3beeptonesmaysound.
t Set the other side edge frequency of the desired
frequency range.
y Push [Y UP] to select the memory channel 2.
 •Selectmemorychannel4or6,respectivelyifthemem-
ory channel 3 or 5 is selected in step e.
u Push [MW 4] for 1 sec. to program the contents into
the memory.
i Repeat steps q to u to program other ranges.
o Push [POWER] for 1 sec. to turn the power OFF
once, then push [POWER] to turn the power
ON while pushing and holding [FM] and [TONE].
 •Thememorychannelscanbeusedfornormaloperation
after programming.
!0 Push [SET] then [FM] to enter the FM set mode.
!1 Push [DN Z] or [Y UP] to select auto repeater item.
 •“AutorPt”isdisplayed.
!2 Rotate the tuning dial to turn the auto repeater func-
tion ON.
 U.S.A.version:
  •“on1” Activatesduplexonly.
  •“on2” Activatesduplexandtone.
  •“oFF” AutorepeaterfunctionisturnedOFF.
 Koreaversion:
  •“ON” Activatesduplexandtone.
  •“OFF” AutorepeaterfunctionisturnedOFF.
!3 Push [FM] to exit from the FM set mode.
NOTE: All repeater ranges for available bands must
be programmed at the same time. Otherwise, the
previously programmed ranges will be lost.
D Frequency range and shift direction
• U.S.A. version
FREQUENCY RANGE SHIFT DIRECTION
145.2000– 145.4999 MHz
146.6100– 146.9999 MHz
“DUP–” appears
147.0000– 147.3999 MHz “DUP+” appears
442.0000– 444.9999 MHz “DUP+” appears
447.0000– 449.9999 MHz “DUP–” appears
1282.0000–1295.9999 MHz “DUP–” appears
• Korea version
FREQUENCY RANGE SHIFT DIRECTION
1439.0000–1440.0000 MHz “DUP–” appears
1290.0000–1293.0000 MHz “DUP–” appears
D Setting the shift direction for the one-touch repeater function
(except Europe, Sweden and Italy versions)
qPush[M/S•BAND]or[SUB]toselectthedesired
frequency band.
w Push [SET] then [FM] to enter the FM set mode.
e
Push [DN Z] or [Y UP] to select shift direction item.
 •“o_touch”and“rPt”aredisplayed.
r Rotate the tuning dial to select the desired direction.
 •“DUP–”or“DUP+”isselectable.
t Push [FM] to exit from the FM set mode.