KITO ER2 Series User Manual

43
■
Checking the Number of the Assembled Adjusting Spacers and Their Positions
When installing a trolley to the beam, the length of the Suspension Shaft (width between frames) must be adjusted in
accordance with the rail width.
Wrong number of wrong position of Spacers may result in the drop of the electric chain hoist.
Insert the correct number of Spacers with correct ratings and for rail width at the correct position, referring to the
following table.
(to be continued)
Assembling Combining with the motorized trolley
1
●
Adjusting spacer arrangement for LOW Head Suspension (Beam flange width 58-149mm)
Remarks) 1) Description for inner spacers
For example, 0+1
0 : the number of spacers on the left side of the shaft
1 : the number of spacers on the right side of the shaft
2) Adjustment of trolley width
Refer to page 45.
Adjust the dimensions by appropriately increasing or decreasing the number of inner or outer adjusting
spacers shown in the above table.
Capacity(t)
Parts
Name
Beam flange width (mm)
58 66 74 82 90 91 98 106 113 119 125 131 137 143 144 149
125kg
250kg
500kg
1t
Thin spacer
Inner 1 2 2 3 4 4 1 2 2 3 2 3 0 0 1 2 2 3 3 4 4 4 5 1 2 2 3 3 3 3 4 4
Outer 8 6 3 8 6 6 11 8 6 4 3 5 7 5 5 3
Thick spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2
Outer 5 5 5 5 5 5 3 3 3 3 3 2 1 1 1 1
Fixing spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Outer 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Thick spacer L
Inner 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Outer 2 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0
1.6t
2t
Thin spacer
Inner 0 1 2 2 2 2 3 3 1 1 2 2 3 3 4 4 1 1 2 2 3 3 3 3 4 0
Outer 7 4 4 2 6 4 2 0 6 4 2 2 4
Thick spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 2
Outer 7 7 7 7 7 7 7 7 5 5 5 5 4
Fixing spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Outer 0 0 0 0 0 0 0 0 0 0 0 0 0
Thick
spacer L
Inner 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Outer 2 2 2 2 0 0 0 0 0 0 0 0 0
2.5t
3.2t
Thin spacer
Inner 1 1 2 2 2 3 3 4 1 1 2 2 3 3 4 4 1 1 2 2 3 3 3 3 4 0
Outer 6 4 3 1 6 4 2 0 6 4 2 2 4
Thick spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 2
Outer 7 7 7 7 7 7 7 7 5 5 5 5 4
Fixing spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Outer 0 0 0 0 0 0 0 0 0 0 0 0 0
Thick
spacer L
Inner 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Outer 2 2 2 2 0 0 0 0 0 0 0 0 0
5t
Thin spacer
Inner 2 2 3 3 4 4 0 0 1 1 2 2 3 3 3 3 4 0
Outer 4 2 0 8 6 4 2 2 4
Thick spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Outer 5 5 5 5 5 5 5 5 4
Fixing spacer
Inner 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Outer 0 0 0 0 0 0 0 0 0
Thick spacer
L
Inner 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Outer 2 2 2 0 0 0 0 0 0

KITO ER2 Series Specifications

General

Control Voltage	24V
Duty Cycle	40% ED
Protection Class	IP55
Temperature Range	-20°C to +40°C
Type	Electric Chain Hoist
Frequency	50/60 Hz
Motor Insulation	Class F
Brake Type	Electromagnetic
Load Chain Grade	Grade 80
Ambient Temperature	-20°C to +40°C
Power Supply	3-phase
Lift Height	3 to 30 meters
Chain Falls	1 or 2
Voltage	200-240V, 380-480V