Krone EasyCut F 360

To Next Page

To Previous Page

Commissioning

Fig.

Pos: 92.12 /La yout Module /---------------Seitenumbruch---------------- @ 0\ mod_11961 75311226_0.doc x @ 4165 @ @ 1

Main Page

Table of Contents3
To this Document6
Validity6
Re-Ordering6
Further Applicable Documents6
Target Group of this Document6
How to Use this Document6
Directories and References6
Direction Information7
Term "Machine7
Figures7
Scope of Document7
Means of Representation7
Safety10
Purpose of Use10
Intended Use10
Service Life of the Machine10
Personnel Qualification and Training11
Dangers in Case of Non-Compliance with the Safety Instructions11
Safety-Conscious Work Practices11
Safety Instructions and Accident Prevention Regulations12
Attached Devices13
PTO Operation14
Hydraulic System15
Maintenance15
Unauthorised Conversion/Modification and Spare Parts Production15
Inadmissible Modes of Operation15
Machine Description16
Machine Overview16
Identification Plate18
Information Required for Questions and Orders18
Contact18
Introduction19
Re-Ordering the Adhesive Safety and Information Labels19
Affixing the Adhesive Safety and Information Labels19
Position of the Adhesive Safety Stickers on the Machine20
Technical Data of the Machine24
Technical Data24
Consumables30
Filling Quantities and Lubrication Designations for Gearboxes30
Ambient Temperature30
Commissioning31
Special Safety Instructions31
First Installation31
Fitting the Guard Cloths32
Installation of Weiste Triangle34
Preparation on the Front-Mounted Disc Mower34
Installation of the Lighting System35
Start-Up36
Preparations on Tractor36
Mounting Onto the Tractor37
Lower Suspension Arm38
Checking the First Fitting39
PTO Shaft40
Length Adjustment40
Install the PTO Shaft41
Mounting and Adjusting the Relief Springs42
Trial Run after First Installation42
Lighting Connection43
Hydraulics44
Special Safety Instructions44
Connecting the Hydraulic Lines44
Driving and Transport46
Lighting46
Operation48
Before Mowing48
Moving the Guards into the Working Position49
Detaching the Machine50
Removing the Compensation Spring(S)50
Settings51
Adjusting the Cutting Height51
Telescopic Upper Suspension Arm52
Adjusting the Compensation Springs53
Maintenance54
Special Safety Instructions54
Test Run54
Spare Parts54
Maintenance Table55
Tightening Torques56
Metric Thread Screws with Control Thread56
Metric Thread Screws with Fine Thread57
Metric Thread Screws with Countersunk Head and Hexagonal Socket57
Deviating Torques57
Rotary Hub with Shear Fuse (Optional)58
After Shearing off60
After Shearing off64
Setting of the V-Belt Tension65
Maintenance - Gearbox66
Angular Gearbox66
Angular Gearbox67
Mower Drive Gearbox68
Mower Drive Gearbox69
Oil Level Check and Oil Change on the Cutter Bar70
Oil Change70
Checking the Oil Level70
Aligning the Cutter Bar70
Maintenance - Blade Changing72
Checking the Cutter Blades and Blade Holder72
Cutter Blades72
Blade Screw Connection73
Blade Quick-Fit Device74
Periodical Inspection of the Leaf Springs75
Periodical Inspection of the Cutting Discs / Blade Drums76
Abrasion Limit77
Blade Changing on Cutting Discs78
Blade Screw Connection79
Blade Quick-Fit Device80
Replacing the Linings81
Maintenance - Lubrication Chart82
Special Safety Instructions82
Lubrication Chart83
Placing in Storage84
Before the Start of the New Season85
Special Safety Instructions85
Test Run85
Friction Clutch86
Special Equipment87
Special Safety Instructions87
Adjusting Skids87
Conversion to Narrower Swathing88
Conversion for Mowing Steep Slopes90
Disposal of the Machine92
Index93

Krone EasyCut F 360 - Page 33

Table of Contents

Other manuals for Krone EasyCut F 360

Related product manuals