Krone EasyCut F 360 - Mower Drive Gearbox

Maintenance - Gearbox
68
Pos: 113 /Übersc hriften/Überschrif ten 2/K-O/MM äherantriebsg etriebe @ 9\ mod_1221045 800746_78.docx @ 131475 @ 2 @ 1
12.3 Mower Drive Gearbox
Pos: 114 /Ab kürzungen /Abkürz ungen sprachne utral/EasyC ut/EasyCut F 2 80 M @ 89\mo d_132273613 0843_0.docx @ 76 6117 @ @ 1
EasyCut F 280 M
Pos: 115 /BA/War tung/Hinweis Ölst andskontroll e in Arbeitsstellu ng und in waager echter Stellung der Maschine vornehmen @ 194\mo d_13835549737 54_78.docx @ 1 649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 116 /BA/War tung/Ölkontroll e_Wechsel/Mä hwerke/Bild Mä herantriebsgetri ebe EC 28/32 @ 10\mod_1 22174150933 3_78.docx @ 13 7196 @ @ 1
Fig.
36
Pos: 117 /BA/War tung/Ölkontroll e_Wechsel/Öl wechsel / Ölko ntrolle:Legende z u Grafik Kontrollsc hraube / Ein füllschraube @ 194\mod_1 38329840777 3_78.docx @ 1 647929 @ @ 1
1)
Inspection screw / control hole
2)
Filler plug / oil filling hole
Pos: 118 /BA/War tung/Ölkontroll e_Wechsel/Ölqu alität /Ölmenge: siehe Kapit el Technische D aten @ 134 \mod_1350483 480921_78.docx @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 119 /BA/War tung/Ölkontroll e_Wechsel/Öl kontrolle / Öl wechsel Inter vall: siehe Kapitel Wartung „Wart ungstabelle“ @ 1 34\mod_13 50483605921_7 8.docx @ 11881 15 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 120 /BA/War tung/Ölkontroll e_WechselÖl kontrolle NEU über Kontrollschr aube @ 140\ mod_13551417 53680_78.doc x @ 1244582 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Screw out filler plug.
• Top up oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 121 /BA/War tung/Ölkontroll e_Wechsel/Öl wechsel NEU ohne Ablassschra ube über Kontr ollschraube @ 194\mod_1 38329876201 4_78.docx @ 1647 958 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out inspection screw and filler plug and drain the oil.
• Top up new oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 122 /BA/War tung/Ölkontroll e_Wechsel/Hin weis - Altöl or dnungsge mäß entsorgen @ 0 \mod_1197008 117002_78.doc x @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 123 /Layou t Module /---------------Seitenumbruch---------------- @ 0\mod_11961753 11226_0.docx @ 4165 @ @ 1