To this Document
6
Pos: 6.1 /Überschrift en/Überschrift en 1/U-Z/Z u diesem Doku ment @ 107\ mod_1334231 929021_78.docx @ 965257 @ 1 @ 1
2 To this Document
Pos: 6.2 /BA/Ei nleitung/Gültigkeit /EasyCut /Gültig keit EasyCut F 280/320/360 2 80/320/360 M @ 103\ mod_133225533066 3_78.docx @ 9 42004 @ 2 @ 1
2.1 Validity
These operating instructions apply to disc mowers of the series:
EasyCut F 280; EasyCut F 320; EasyCut F 360,
EasyCut F 280 M; EasyCut F 320 M, EasyCut F 360 M
Pos: 6.3.1 /Übers chriften/Überschri ften 2/K-O/N/N achbestell ung (Nachbest ellung dieses D okuments) @ 349\mod_14363 55974813_78.d ocx @ 262586 5 @ 2 @ 1
2.2 Re-Ordering
Pos: 6.3.2 /BA/Zu diesem Dokum ent/Nachbestellu ng_Text @ 3 49\mod_1436 355830140_7 8.docx @ 2625 835 @ @ 1
If this document should become wholly or partially unusable, you can request a replacement
document by stating the order number mentioned on the cover sheet.
Pos: 6.4 /Überschrift en/Überschrift en 2/K-O/MMi tgeltende Do kumente @ 187\ mod_138011 3031071_78.d ocx @ 160966 4 @ 2 @ 1
2.3 Further applicable documents
Pos: 6.5 /BA/Zu di esem Do kument/Mitgeltende Do kumente_Ei nführungssatz_ alle Maschinen @ 187\mod_ 13801139404 83_78.docx @ 1609940 @ @ 1
To ensure that the machine is used safely and as intended, observe the following further
applicable documents:
Pos: 6.6 /BA/Zu di esem Do kument/Mitgeltende Do kumente_Eas yCut @ 364 \mod_144060 1387970_78. docx @ 2681556 @ @ 1
– Operating instructions of universal shaft
Pos: 6.7 /Überschrift en/Überschrift en 2/U-Z/ZZi elgruppe dies es Dokuments @ 187\mod_1 380113123454_7 8.docx @ 16 09723 @ 2 @ 1
2.4 Target group of this document
Pos: 6.8 /BA/Zu di esem Do kument/Zielgrupp e @ 345\mod_1 434348246902 _78.docx @ 2606935 @ @ 1
This document aims at the operators of the machine fulfilling the minimum requirements of
personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.
Pos: 6.9.1 /Übers chriften/Überschri ften 2/P-T /SSo benutzen Sie dieses Do kument @ 188\m od_13805483 50021_78.doc x @ 1614365 @ 2 @ 1
2.5 How to use this document
Pos: 6.9.2 /Übers chriften/Überschri ften 3/U-Z/ Verzeichnisse und Verweise @ 336\mod_ 1429854437094_7 8.docx @ 255 6421 @ 3 @ 1
2.5.1 Directories and References
Pos: 6.9.3 /BA/Zu diesem Dokum ent/So benutze n Sie dieses D okument_Verzeic hnisse und Verweise_Te xt @ 333\mod_ 142908537840 8_78.docx @ 2 544425 @ @ 1
Table of contents/headers:
The table of contents as well as the headers in this instruction are used for quick navigation in
the chapters.
Index directory:
In the index directory, you can find information on the desired subject via catchwords which are
in alphabetical order. The index directory can be found on the last page of this instruction.
Cross references:
Cross references to another place in the operating instructions or to another document are in
the text and specify the chapter and subchapter or section. The designation of subchapters or
sections is presented in quotation marks.
Example:
Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening
Torques”.
The subchapter or the section can be found via an entry in the table of contents and in the index
directory.
Pos: 6.9.4 /Layo ut Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0.d ocx @ 4165 @ @ 1
To Next Page
Loading...
