Maintenance - Gearbox
66
Pos: 108 /Übersc hriften/Überschrif ten 1/U-Z/W artung - Getrie be @ 2\mod_ 1203058202823_ 78.docx @ 6 4495 @ 1 @ 1
12 Maintenance - Gearbox
Pos: 109.1 /Übersc hriften/Überschrif ten 2/U-Z/ WWinkelgetrie be @ 0\mod_1 19700591829 9_78.docx @ 1 5435 @ 2 @ 1
12.1 Angular gearbox
Pos: 109.2 /Ab kürzungen /Abkürz ungen sprac hneutral/EasyC ut/EasyCut F 280 / EasyCut F 3 20 / EasyCut F 3 60 @ 103\ mod_1332231 912643_0.doc x @ 940949 @ @ 1
EasyCut F 280 / EasyCut F 320 / EasyCut F 360
Pos: 109.3 /BA/ Wartung/Hinweis Ölstandsko ntrolle in Arbeitsst ellung und in waagerechter Stellu ng der Maschin e vornehmen @ 194\mo d_138355497 3754_78.docx @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 109.4 /BA/ Wartung/Ölkontroll e_Wechsel/M ähwerke/Bild Wi nkelgetriebe EC 28/32 @ 10\ mod_12217 40931598_78.d ocx @ 137129 @ @ 1
Fig.
Pos: 109.5 /BA/ Wartung/Ölkontroll e_Wechsel/Öl wechsel / Ölko ntrolle:Legende z u Grafik Kon trollschraube @ 204\mod_1 38616322515 0_78.docx @ 1 702532 @ @ 1
Inspection screw / control hole
Pos: 109.6 /BA/ Wartung/Ölkontroll e_Wechsel/Ölq ualität /Öl menge: siehe Kapitel Technisch e Daten @ 1 34\mod_1350 483480921_78. docx @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 109.7 /BA/ Wartung/Ölkontroll e_Wechsel/Öl kontrolle / Öl wechsel Inter vall: siehe Kapitel Wartung „Wart ungstabelle“ @ 134\mod_13 50483605921_7 8.docx @ 11 88115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 109.8 /BA/ Wartung/Ölkontroll e_WechselÖl kontrolle NEU über Kontrollschr aube ohne Einf üllschraub e @ 158\mod_ 1364483633589 _78.docx @ 139 1741 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Top up oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 109.9 /BA/ Wartung/Ölkontroll e_Wechsel/Öl wechsel NEU Öl absaugen @ 2 04\mod _1386163484591_ 78.docx @ 17 02591 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out inspection screw.
• Draw off oil.
• Top up new oil via control hole up to the control hole.
• Screw in inspection screw and tighten it securely.
Pos: 109.10 /BA /Wartung/Öl kontrolle_Wechs el/Hinweis - Altöl ordnungsgem äß entsorgen @ 0\mod_119 7008117002_78 .docx @ 1555 0 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 110 /Layou t Module /---------------Seitenumbruch---------------- @ 0\mod_11961753 11226_0.docx @ 4165 @ @ 1
To Next Page
Loading...
