Krone Swadro TC 680 - Checking; Setting Distance between Tine Arm and Outrigger Arm

Commissioning
52
Pos: 28.24 /Übersc hriften/Überschri ften 2/A-E/A/Abstand z wischen Zinkenarm und Aus legearm prüfen / einstel len @ 299\mod_141286726 3499_78.docx @ 2340280 @ 2 @ 1
7.6 Checking / Setting Distance Between Tine Arm and Outrigger Arm
Pos: 28.25 /BA/Sic herheit/6. Überarbeite te Warnhinweise/Ac htung - Maß X1 einstellen @ 300\ mod_1413297278218_78. docx @ 2347945 @ @ 1
CAUTION!
The machine may be damaged if the dimension X1 is not set.
• Check dimension X1 and set it, if necessary.
Pos: 28.26 /BA/Er stinbetriebnahme/Sch wader/Swadro TS 620 (Twin) / TS 680T (Twin)/ TS 740 (Twin) /Einstellung Zwisc henlenker Swadro TS 620/ TS 680/ TS 740/TC 880_Aufkleber @ 307\mod_1416386747285 _78.docx @ 2383342 @ @ 1
27 016 473 0
1
2
Fig. 21
Pos: 28.27 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_134259291814 5_0.docx @ 1092566 @ @ 1
Pos: 28.28 /BA/Er stinbetriebnahme/Sch wader/Swadro TC 880/Ein stellung der Zugstrebe S wadro TC 880_Bild @ 313\mod_14 21238378723_78.doc x @ 2418306 @ @ 1
4
TC880-001
5
3
1
2
Fig.22
Pos: 28.29 /BA/Er stinbetriebnahme/Sch wader/Swadro TS 620 (Twin) / TS 680T (Twin)/ TS 740 (Twin) /Einstellung der Zugs trebe Swadro TS 620 / TS 680 / TS 740/ TC 880 _Voraussetzung @ 382\m od_1444216295678_78. docx @ 2754329 @ @ 1
Prerequisite:
– The machine is in headland position and the outrigger arms are completely retracted.
Pos: 28.30 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_134259291814 5_0.docx @ 1092566 @ @ 1
Pos: 28.31 /BA/Er stinbetriebnahme/Sch wader/Swadro TC 880/Abst and Zinkenarm zu Aushubzy linder TC 880_Zusatz @ 317\ mod_1423055400 692_78.docx @ 2448806 @ @ 1
• In order to achieve the shortest possible distance between tine arm and lifting cylinder,
press tine arm towards outrigger arm.
Pos: 28.32 /BA/Er stinbetriebnahme/Sch wader/Swadro TS 620 (Twin) / TS 680T (Twin)/ TS 740 (Twin) /Einstellung der Zugs trebe Swadro TS 620 / TS 680 / TS 740/ TC 880 _Text @ 317\mod_142312 5603582_78.doc x @ 2453445 @ @ 1
• Measure the distance X1 between tine arm (1) and outrigger arm (2).
If the dimension is X1 ≥ 100 mm, everything is OK.
If the dimension is not X1 ≥ 100 mm, the distance must be set via intermediate link.
• Dismount bolt (4).
• Loosen counter nut (5).
• Turn the intermediate link (3) until the dimension X1 ≥ 100 mm is set.
• Tighten counter nut (5).
• Mount bolt (4).
Pos: 28.33 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1