Krone Swadro TC 680 - Setting the Spreading Angle of the Additional Rotor

To Next Page

To Previous Page

Settings

Pos: 36.18 /Übersc hriften/Überschri ften 2/P-T/S/Streuwin kel des Zusatzkreise ls einstellen @ 167\mod _1367903252028_78.doc x @ 1450365 @ 2 @ 1

11.5 Setting the Spreading Angle of the Additional Rotor

Pos: 36.19 /Übersc hriften/Zwischenüber schriften/A-E/ Bei Ausführung "Zusatzkr eisel" @ 504\mod_1498 545699491_78.docx @ 347 2908 @ @ 1

For version with “additional rotor”

Pos: 36.20 /BA/Ei nstellungen/Schwader /Streuwinkel Zusa tzkreisel/Hinweis - Streuwinkeleinst ellung SW 800/26 Zusatzkr eisel @ 167\mod_13675 13033468_78.docx @ 1446 716 @ @ 1

Note

The spreading angle of the rotor tines can be adjusted to the conditions of ground and grit by

using the adjustment spindle (1).

Pos: 36.21 /BA/Ei nstellungen/Schwader /Streuwinkel Zusa tzkreisel/Streu winkeleinstellun g_Bild_SW 800/826 Zusa tzkreisel @ 427\mod_14 55093269203_78.doc x @ 2960536 @ @ 1

SW700108_1

Fig. 65

Pos: 36.22 /BA/Einste llungen/Wender/ Flachster Streuwinke l @ 16\mod_1235652885221 _78.docx @ 200428 @ @ 1

Taken as a basis for the spreading angle setting:

Flattest spreading angle II:

• big scattering width

• short crop

• wide lying crop

• forage less than 40% moisture content

Pos: 36.23 /BA/Einste llungen/Wender/ Steilster Streuwinkel @ 20\ mod_1238594946738_ 78.docx @ 223860 @ @ 1

Steepest spreading angle I:

• high discharge distance

• long crop

• better spreading effect with swaths

• wilted silage

• forage more than 40% moisture content

Pos: 36.24 /BA/Einste llungen/Schwader/ Streuwinkel Zusatzkr eisel/Streu winkel einstellen_Zwi schenüberschrif t_SW 800/26 Zusatzkreise l @ 168\mod_1368024832 844_78.docx @ 1453615 @ @ 1

Setting the spreading angle

Pos: 36.25 /BA/Einste llungen/Schwader/ Streuwinkel Zusatzkr eiselAchtung - Kol lision Zinkenarme mi t Schutzrohr SW 800/26 Zusat zkreisel (2017- 08-02 08:25:01) @ 167\mod_13 67906664463_78.doc x @ 1450679 @ @ 1

CAUTION!

Damages to the machine as the tine arms (3) collide with the protective tube (4) of the

universal shaft.

• Dimension (b) must be at least 3 cm to prevent damages. Make certain the dimension (a)

does not exceed 40 cm.

Pos: 36.26 /BA/Ei nstellungen/Schwader /Streuwinkel Zusa tzkreisel/Streu winkeleinstellun g_Text_SW 800/26 Zusat zkreisel @ 167\mod_136 7845662242_78.doc x @ 1449045 @ @ 1

• Loosen the counter nuts (2).

• Reduce dimension (a) to get a steeper spreading angle.

• Increase dimension (b) to get a flatter spreading angle.

• Tighten the counter nuts (2).

Pos: 36.27 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1