Krone Swadro TC 680 - Rotor Inclination Adjustments

Settings
92
Pos: 36.6.1 /Überschr iften/Überschr iften 2/K-O/KKreisel neigung einstellen @ 191\ mod_1381819931154 _78.docx @ 1631074 @ 2 @ 1
11.1 Setting the Rotor Inclination
Pos: 36.6.2 /BA/Ei nstellungen/Schwader /Kreiselfahrwerk/ Kreiselneigung ei nstellen Text Einlei tung Swadro TC 680_TC 760 @ 223\mod_1 392114706229_78.doc x @ 1808993 @ @ 1
The rotor pitch angle has been set at a transverse angle to the chassis in the factory. If the
crops are not picked up properly, the working quality can be improved by adjusting the rotor
pitch.
The rotor pitch angle is adjusted for each rotor via the guide wheels at the chassis. The best
results are achieved if the rotor pitch adjustment ensures the tines are closer to the ground level
when outputting the crops than at the start when picking up the crops.
Pos: 36.6.3 /BA/Si cherheit/8. Vor aussetzungen/Handlungsan weisung für alle Maschi nen/Handlungsanweis ung: Maschine stil lsetzen und sicher n @ 274\mod_1404365253849_78. docx @ 2065151 @ @ 1
• Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting
down and safeguarding the machine".
Pos: 36.6.4 /Layout Modu le /--------- -------Leerzeile-------------------- @ 240\mod_1395147357027_0. docx @ 1890988 @ @ 1
Pos: 36.6.5 /Überschr iften/Überschr iften 3/K-O/KKreiself ahrwerk (Serie) @ 223\mod_1392126168498_78.d ocx @ 1810305 @ 3 @ 1
11.1.1 Rotor chassis (serial)
Pos: 36.6.6 /BA/Ei nstellungen/Schwader /Kreiselfahrwerk/ Kreiselfahrwerk Bil d Swadro TC 680_TC 760_TS 620_ TS 680 @ 247\mod_1396424074075 _78.docx @ 1925403 @ @ 1
SW700077_2
I
II
+
1
Fig. 59
Pos: 36.6.7 /Layout Modu le /--------- -------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145 _0.docx @ 1092566 @ @ 1
Pos: 36.6.8 /BA/Ei nstellungen/Schwader /Kreiselfahr werkKreiselneigung eins tellen Text Position_ äußeres Tandemfahr werk @ 466\mod_1467970075 772_78.docx @ 3140777 @ @ 1
Pos. I = reduce rotor inclination
Pos. II = increase rotor inclination
Pos: 36.6.9 /BA/Ei nstellungen/Schwader /Kreiselfahr werkKreiselfahrwerk Vor gehensweise Swadro di verse TC und TS @ 427\mod_145503 2842030_78.doc x @ 2959284 @ @ 1
Do not step under the raised rotors.
• Only raise the outrigger arms as far as necessary to perform the changeover work.
• To set rotor inclination, dismount the rear guide wheels and move them in the hole pattern.
For better orientation, observe the basic setting of rotor inclination, refer to chapter Initial
Operation, “Rotor Inclination - Basic Setting”.
Pos: 36.6.10 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Kreiselfahrwer k Feinjustierung E xzenter_Mittel- und Sei tenschwader @ 247\mod_139 6419059030_78.doc x @ 1924843 @ @ 1
Vernier adjustment via eccentric cam (1):
− = Reducing rotor inclination
+ = Increasing rotor inclination
Pos: 36.6.11 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Kreiselneigung ei nstellen über Exzenter im Radbolzen Swadro TC 680_ TC 760 _TC 880 @ 303\mod_14141446 84500_78.docx @ 2357644 @ @ 1
Do not step under the raised rotors.
• Raise the outrigger arms until the changeover work can be performed.
• Loosen the nut of the wheel bolt.
• Turn the eccentric (1) to set the rotor inclination.
• Tighten the nut of wheel bolt.
Pos: 36.6.12 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Hinweis schweres Fu tter - Fahrwerk innen mög lichst niedrig einstel len @ 4\mod_121308483822 6_78.docx @ 86157 @ @ 1
Note
If the forage is heavy, adjust the inner running gear as low as possible!
Pos: 36.6.13 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.d ocx @ 4165 @ @ 1