Krone Swadro TC 680 - For the Trailing Guide Wheels Version

Settings
93
Pos: 36.6.14 /Überschr iften/Überschr iften 3/A-E/BBei Ausf ührung "Nachlaufende Tasträder" @ 427\mod_1455 009765507_78.doc x @ 2957230 @ 3 @ 1
11.1.2 For the “Trailing Guide Wheels” Version
Pos: 36.6.15 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Kreiselfahrwer k Bild nachlaufendes Rad Swadro TC 680_TC 760_TS 620_ TS 680 @ 247\mod_1396423997182 _78.docx @ 1925374 @ @ 1
I
I
I
SW700091_1
3
1
2
III
Fig. 60
Pos: 36.6.16 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.doc x @ 1092566 @ @ 1
Pos: 36.6.17 /BA/Ei nstellungen/Schwader /Kreiselfahr werkKreiselneigung eins tellen Text Position _äußeres Tandemfahr werk @ 466\mod_146797007 5772_78.docx @ 3140777 @ @ 1
Pos. I = reduce rotor inclination
Pos. II = increase rotor inclination
Pos: 36.6.18 /BA/Ei nstellungen/Schwader /Kreiselfahr werkKreiselfahrwerk Vor gehensweise Swadro di verse TC und TS @ 427\mod_14550 32842030_78.doc x @ 2959284 @ @ 1
Do not step under the raised rotors.
• Only raise the outrigger arms as far as necessary to perform the changeover work.
• To set rotor inclination, dismount the rear guide wheels and move them in the hole pattern.
For better orientation, observe the basic setting of rotor inclination, refer to chapter Initial
Operation, “Rotor Inclination - Basic Setting”.
Pos: 36.6.19 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Kreiselneigung ei nstellen über Langloc h_Mittel- und Seitensc hwader @ 247\mod_1396418 696967_78.doc x @ 1924755 @ @ 1
Vernier adjustment by the screw on the oblong hole (3):
− = Reducing rotor inclination
+ = Increasing rotor inclination
Pos: 36.6.20 /BA/Ei nstellungen/Schwader /Kreiselfahr werkKreiselneigung Vorge hensweise Langloc h_Mittel- und Seitensc hwader @ 306\mod_141586 5553813_78.docx @ 23756 28 @ @ 1
Do not step under the raised rotors.
• Raise the rotor arms only far enough to be able to perform changeover task.
• Loosen the counter nut (1).
• To be able to adjust the guide wheel, turn the stop screw (2) several threads to the top.
• Loosen the nuts (3) until the screws are not loosened completely so that the guide wheel
does not slip.
• Move the guide wheel to set the rotor inclination.
• Fix the adjustment hand-tight by using the stop screw (2).
• Tighten counter nut (1).
• Tighten the nuts (3) with a tightening torque of 200 Nm.
Pos: 36.6.21 /BA/Ei nstellungen/Schwader /Kreiselfahr werk/Hinweis schweres Fu tter - Fahrwerk innen mög lichst niedrig einstel len @ 4\mod_121308483822 6_78.docx @ 86157 @ @ 1
Note
If the forage is heavy, adjust the inner running gear as low as possible!
Pos: 36.6.22 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.d ocx @ 4165 @ @ 1