To this Document
7
Pos: 5 /Überschrif ten/Überschrif ten 1/U-Z/Zu diesem Dokument @ 107\ mod_1334231929021_78. docx @ 965257 @ 1 @ 1
2 To this Document
Pos: 6 /BA/Einleitun g/Gültigkeit/Sc hwader/Gültigkei t Swadro TC 680_TC 760 @ 293\mod_1411 395491091_78.doc x @ 2305171 @ 2 @ 1
2.1 Validity
These operating instructions apply to rotary rakes of the series:
Swadro TC 680, Swadro TC 760
Pos: 7.1 /Überschri ften/Überschri ften 2/K-O/N/Nachbeste llung (Nachbestellun g dieses Dokuments) @ 349\ mod_1436355974813_7 8.docx @ 2625865 @ 2 @ 1
2.2 Re-Ordering
Pos: 7.2 /BA/Zu diesem Dok umentNachbestellun g_Text (2017-08-10 16: 09:56) @ 349\mod_14363 55830140_78.docx @ 2625 835 @ @ 1
If this document should become wholly or partially unusable, you can request a replacement
document by stating the order number mentioned on the cover sheet.
Pos: 8 /Überschrif ten/Überschrif ten 2/K-O/M/Mitgeltende Doku mente @ 187\mod_13801 13031071_78.docx @ 1609664 @ 2 @ 1
2.3 Further applicable documents
Pos: 9 /BA/Zu diesem Doku ment/Mitgeltende Doku mente_Einführung ssatz_alle Maschi nen @ 187\mod_1380113940483 _78.docx @ 1609940 @ @ 1
To ensure that the machine is used safely and as intended, observe the following further
applicable documents:
Pos: 10 /BA/Zu diesem Doku ment/Mitgeltende Doku mente_Betriebsa nleitung(en) Gelenk welle(n) @ 347\mod_1435588 572591_78.doc x @ 2616249 @ @ 1
– Operating instructions of universal shaft(s)
Pos: 11 /Überschrif ten/Überschrif ten 2/U-Z/Z/Zielgruppe di eses Dokuments @ 187\mod_1 380113123454_78.d ocx @ 1609723 @ 2 @ 1
2.4 Target group of this document
Pos: 12 /BA/Zu diesem Doku ment/Zielgruppe @ 345\ mod_1434348246902_78. docx @ 2606935 @ @ 1
This document aims at the operators of the machine fulfilling the minimum requirements of
personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.
Pos: 13.1 /Überschri ften/Überschri ften 2/P-T/SSo benutzen Sie di eses Dokument @ 188\mod_138 0548350021_78.doc x @ 1614365 @ 2 @ 1
2.5 How to use this document
Pos: 13.2 /Überschri ften/Überschri ften 3/U-Z/Verzeichni sse und Verweise @ 336\mod_1 429854437094_78.d ocx @ 2556421 @ 3 @ 1
2.5.1 Directories and References
Pos: 13.3 /BA/Zu diesem Do kument/So benutzen Sie di eses Dokument_Verzei chnisse und Verweise_ Text @ 333\mod_142908537 8408_78.docx @ 2544425 @ @ 1
Table of contents/headers:
The table of contents as well as the headers in this instruction are used for quick navigation in
the chapters.
Index directory:
In the index directory, you can find information on the desired subject via catchwords which are
in alphabetical order. The index directory can be found on the last page of this instruction.
Cross references:
Cross references to another place in the operating instructions or to another document are in
the text and specify the chapter and subchapter or section. The designation of subchapters or
sections is presented in quotation marks.
Example:
Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening
Torques”.
The subchapter or the section can be found via an entry in the table of contents and in the index
directory.
Pos: 13.4 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_119617531122 6_0.docx @ 4165 @ @ 1